5
WARNING! Verify that your chosen location
is level, has a solid base, and will be in full
view of competent adult supervision when in use.
Step 22 WARNING! For Maximum stability, the
ladder must be fastened to the top of the pool.
18.
Coat the adjustable tubes with a small
amount of liquid soap and slide the
tube up through the mounting block
as shown.
4
3
If your Confer pool step is not in
the pool follow the step
instructions and place in pool.
Choose a location for your
Confer pool ladder/step
combination that is in full
view at all times. Always have
adult supervision when pool
is in use. Always swing up
outside treads and lock when
pool is not in use.
19.
Slide the asssembled tube/block
assembly up into the open end of the
adjustable tube handrail as shown.
Ladder is now ready to attach to Confer
Plastics In-Pool Step.
20.
With the step in location place your 8100x ladder over the
pool wall. Depending on the outside height of swimming
pool ledge extension boots can be removed or slid up or
down until the ladder platform is resting on top of the
swimming pool top ledge. If necessary remove or add soil
to raise or lower ladder. The 8100x ladder platform must
rest on top of the swimming pool ledge for support.
21.
With the ladder in place and platform resting on pool ledge
extend the adjustable tubes down until the mounting
blocks are resting on the top tread of pool step. Next move
the ladder in or out to position the platform mounting holes
to the outside [away from pool wall] top of pool ledge.
22.
Pool ladder must be attached to swimming pool ledge.
Mark the two positions on to the top ledge. Move the ladder
away, check to make sure the hole locations are clear of
pool wall and supports and drill two 5/16 holes through the
top ledge. Fasten the ladder platform to the top ledge using
two ¼-20 x 2-1/4” bolts, flat washers and ¼-20 hex nuts.
Repeat to attach the two step deck connectors.
23.
Using a cordless drill/driver attach the two mounting
blocks to the pool step using eight [8] #10 x 1-1/4”
screws. Secure the adjustable tubes to the adjustable
tube handrail at the pre-marked locations using two
[2] #10 x 1-1/4” screws in each handrail.
he flat
x 1”
Place
d area
7.
nd
et
t-
v-
et
Hole
Locations
prpd.RG-Confer 8100X-11-13_Confer 6100_12-05_R1 11/22/13 9:15 AM Page 4
WARNING! Using a corded drill near pool
may result in electrocution.
18.
Coat the adjustable tubes with a small
amount of liquid soap and slide the
tube up through the mounting block
as shown.
4
3
If your Confer pool step is not in
the pool follow the step
instructions and place in pool.
Choose a location for your
Confer pool ladder/step
combination that is in full
view at all times. Always have
adult supervision when pool
is in use. Always swing up
outside treads and lock when
pool is not in use.
19.
Slide the asssembled tube/block
assembly up into the open end of the
adjustable tube handrail as shown.
Ladder is now ready to attach to Confer
Plastics In-Pool Step.
20.
With the step in location place your 8100x ladder over the
pool wall. Depending on the outside height of swimming
pool ledge extension boots can be removed or slid up or
down until the ladder platform is resting on top of the
swimming pool top ledge. If necessary remove or add soil
to raise or lower ladder. The 8100x ladder platform must
rest on top of the swimming pool ledge for support.
21.
With the ladder in place and platform resting on pool ledge
extend the adjustable tubes down until the mounting
blocks are resting on the top tread of pool step. Next move
the ladder in or out to position the platform mounting holes
to the outside [away from pool wall] top of pool ledge.
22.
Pool ladder must be attached to swimming pool ledge.
Mark the two positions on to the top ledge. Move the ladder
away, check to make sure the hole locations are clear of
pool wall and supports and drill two 5/16 holes through the
top ledge. Fasten the ladder platform to the top ledge using
two ¼-20 x 2-1/4” bolts, flat washers and ¼-20 hex nuts.
Repeat to attach the two step deck connectors.
23.
Using a cordless drill/driver attach the two mounting
blocks to the pool step using eight [8] #10 x 1-1/4”
screws. Secure the adjustable tubes to the adjustable
tube handrail at the pre-marked locations using two
[2] #10 x 1-1/4” screws in each handrail.
he flat
x 1”
Place
d area
7.
nd
et
t-
v-
et
Hole
Locations
prpd.RG-Confer 8100X-11-13_Confer 6100_12-05_R1 11/22/13 9:15 AM Page 4
WARNING! when pool
is NOT IN USE, keep
the outer treads in the
up position and locked
with the padlock.
To close ladder:
move
“Swing up” portion of
ladder shown in “up”
position as shown and
secure with included
padlock.
Swing Up Instructions
To use ladder:
unlock the
padlock and move it to the
“holding” area.
Move “Swing” portion of
the ladder to the “down”
position as shown.
18.
Coat the adjustable tubes with a small
amount of liquid soap and slide the
tube up through the mounting block
as shown.
4
3
If your Confer pool step is not in
the pool follow the step
instructions and place in pool.
Choose a location for your
Confer pool ladder/step
combination that is in full
view at all times. Always have
adult supervision when pool
is in use. Always swing up
outside treads and lock when
pool is not in use.
19.
Slide the asssembled tube/block
assembly up into the open end of the
adjustable tube handrail as shown.
Ladder is now ready to attach to Confer
Plastics In-Pool Step.
20.
With the step in location place your 8100x ladder over the
pool wall. Depending on the outside height of swimming
pool ledge extension boots can be removed or slid up or
down until the ladder platform is resting on top of the
swimming pool top ledge. If necessary remove or add soil
to raise or lower ladder. The 8100x ladder platform must
rest on top of the swimming pool ledge for support.
21.
With the ladder in place and platform resting on pool ledge
extend the adjustable tubes down until the mounting
blocks are resting on the top tread of pool step. Next move
the ladder in or out to position the platform mounting holes
to the outside [away from pool wall] top of pool ledge.
22.
Pool ladder must be attached to swimming pool ledge.
Mark the two positions on to the top ledge. Move the ladder
away, check to make sure the hole locations are clear of
pool wall and supports and drill two 5/16 holes through the
top ledge. Fasten the ladder platform to the top ledge using
two ¼-20 x 2-1/4” bolts, flat washers and ¼-20 hex nuts.
Repeat to attach the two step deck connectors.
23.
Using a cordless drill/driver attach the two mounting
blocks to the pool step using eight [8] #10 x 1-1/4”
screws. Secure the adjustable tubes to the adjustable
tube handrail at the pre-marked locations using two
[2] #10 x 1-1/4” screws in each handrail.
he flat
x 1”
Place
d area
7.
nd
et
t-
v-
et
Hole
Locations
prpd.RG-Confer 8100X-11-13_Confer 6100_12-05_R1 11/22/13 9:15 AM Page 4
to raise or lower ladder.
The 8100X ladder platform must
rest on top of the swimming pool ledge for support.