Hardware Pack
14 - #10 x 1-1/4” screws
2 - Plugs (wg)
2 - 1/4 - 20 x 2” Bolts
2 - 1/4 - 20 Acorn Nuts
2 - Adjustable Tubes
2 - Mounting Blocks
4 - 1/4 - 20 x 2-1/4” Bolts
4 - 1/4 - Flat Washers
8 - 1/4 - 20 Hex Nuts
4 - 1/4 - 20 x 1” Bolts
1 - Padlock
Tools Needed for Assembly
* - Rubber mallet
* - Adjustable wrench
* - Cordless Drill
* - 5/16” Drill Bit
* - Phillips Screwdriver
or screwdriver bits
* - Pliers
* - Liquid soap or lubricant
Parts List
2 - Ladder Legs
2 - Tread Connector
4 - Swing up Treads
1 - Standard Tread
2 - Extension Boots
1 - Platform
2 - Handrails
2 - Adjustable Tube Handrails
Use a little liquid soap to
help with ladder assembly.
Model #8100X
Outside Safety Ladder
Ladder must be attached to pool frame -
DO NOT USE
with inflatable pools
If missing parts call - Toll free U.S./Canada - 800-635-3213 or www.conferladders.com
Safe Installation
To reduce the risk of electrocution, drowning, entrapment, falls, or other serious
injury or death:
Check building codes/permitting.
Consult your local Building Department before installation of your pool and
equipment. Pool/equipment installation must comply with the codes of the authority having jurisdiction and may require
permits (e.g., building, plumbing, electrical, zoning, etc.).
Use for intended purpose only
• Use only as a swimming pool ladder.
• This ladder is designed and manufactured for a specific pool wall height and/or deck of the pool - check product
specification and the height of your pool.
Check that you have all required parts.
Check the contents of the carton with the Parts List for this ladder. All parts and
hardware are required. If any parts are missing,
DO NOT attempt to assemble or install the ladder.
Instead, call Toll
Free U.S. - 800-635-3213 or visit our web site at www.conferladders.com for assistance.
Select an appropriate location
- The ladder must be located on a level, solid base and in a location that will be in full
view of competent adult supervision when in use.
Follow all instructions
• For stable, correct assembly and installation, all instructions must be followed completely and in the sequence shown.
• Follow the manufacturer’s recommendations for the safe use of all hand tools and equipment used during installation.
Cordless drill only - no corded drills near pool.
Use a cordless drill for assembly and installation. To reduce the risk of
electrocution, NEVER use a corded drill in or around a pool.
Lift safely.
When lifting awkward or heavy loads, have another person help you.
Double check after installation
• Before using the product, after assembly and installation, go over the instructions and procedures again to make sure
nothing has been overlooked.
• Make sure that safety labels are installed and legible.
2
Hardware Pack
14- #10 x 1-1/4" screws
2 - Plugs (wg)
2 - 1/4 - 20 x 2" Bolts
2 - 1/4 - 20 Acorn Nuts
2 - Adjustable Tubes
2 - Mounting Blocks
4 - 1/4 - 20 x 2 1/4" Bolts
4 - 1/4 - Flat Washers
8 - 1/4 - 20 Hex Nuts
4 - 1/4 - 20 x 1" Bolts
1 - Padlock
Needed for Assembly
- Rubber mallet
- Phillips screwdriver
- Adjustable wrench
- Liquid soap or lubricant
- Cordless Drill / Phillips Driver
- 5/16” Drill bit
Model #8100X
Outside Safety Ladder
ASSEMBLY INSTRUCTIONS - PLEASE READ BEFORE ATTEMPTING ASSEMBLY
Parts List
2 - Ladder Legs
2 - Tread Connectors
4 - Swing up Treads
1 - Standard Tread
2 - Extension Boots
1 - Platform
2 - Handrails
2 - Adjustable Tube Handrails
If missing parts call - Toll free U.S. - 800-635-3213 or www.Conferplastics.com
For Use with Confer Plastics In-Pool Step
ADJUSTABLE
TUBE
HANDRAILS
TREAD
CONNECTIORS
SWING UP
TREAD
MOUNTING
BLOCKS
PLATFORM
LADDER
LEGS
1.
Place (2) two ladder legs on a flat
surface. Using a Phillips screwdriv-
er tap out the plastic film from the
three holes on the bottom of
each leg.
Using two 1/4-20 x 2” long bolts and
two acorn nuts fasten the extension
boots to the ladder legs
Slide (4) four of the swing up treads
over the ladder legs as shown.
2.
3.
Slip the (2) two extension boots over
the ends of the ladder legs. They will
need to be all the way on if the
outside dimension is 52" and backed
off one hole if the outside dimension
is 54".
4.
5.
2
STANDARD
TREAD
Se
lad
9
HANDRAIL
6
St
th
th
th
en
Extension boots are not required if
the outside height of your pool
(measured from the ground to the
top of the pool ledge) is 48" or less.
If this measurement is more than
48" extension boots will be
required. Using a Phillips screwdriver
tap out the plastic film from the top
hole on each side of the extension
boots.
At
by
1
Sl
th
th
ADJUSTABLE
TUBES
EXTENSION
BOOT
prpd.RG-Confer 8100X-11-13_Confer 6100_12-05_R1 11/22/13 9:15 AM Page 2
IMPORTANT: LADDER ADAPTER KIT
LAK
kit fits Confer A-frame ladders for use with non-traditional
metal framed swimming pools with a wall height of 48” - 54”.
Use with models: 7100b, 7100x, 7000b, 7200 and 7000x.
Not for use with inflatable pools.
LAK KIT