4
er
ill
d
11.
1
C
am
tu
as
3
Separate the swing up assembly from the
ladder legs and set aside.
9.
Slide (2) two handrails up through the bot-
tom of the platform using the openings next
to the round tabs. Leave the flat ends of the
handrails exposed.
10.
2
W
po
po
do
sw
to
re
2
P
M
aw
po
to
tw
R
6.
7.
Stand the assembly up on edge and place
the tread connector over the square ends on
the (4) four treads. The large oval hole on
the tread connector must be on the same
end as the flat side on the ladder legs.
Using a rubber mallet tap the tread connec-
tor onto the square ends of the treads until
they are firmly seated. A little liquid soap on
the tread end will help.
Flip assembly over and repeat step 7 to
attach the second tread connector.
Overlap the flat end of the ladder leg onto the flat
end of the handrail. Insert one of the ¼ - 20 x 1”
bolt through the ladder leg into the handrail. Place
one of the ¼ - 20 hex nuts into the recessed area
on the handrail and tighten using a Phillips
screwdriver. Install the second nut and bolt.
14.
Attach the second ladder leg to the handrail
by repeating step #11.
12.
Stand the ladder up, using a rubber mallet tap the
platform down until seated on the lugs on the ladder
leg. IT WILL REQUIRE SEVERAL HARD BLOWS
WITH A RUBBER MALLET TO SEAT THE PLAT-
FORM ALL THE WAY DOWN ONTO LUGS.
13.
Attach the standard tread to the bottom of
the ladder as shown.
17.
Slide the (2) two adjustable tube handrails up
through the bottom of platform until seated on
the lugs.
15.
Flex the oval openings on the swing up
assembly (from step #9) over the two round
tabs on the platform. Using a rubber mallet
tap down on the tread connector until seat-
ed over the round tab. It may require sev-
eral hard hits with a rubber mallet to get
tread connector over round tabs.
16.
Using a #10 x 1-1/4” screw fasten the
upper ends of the handrails together as
shown. Repeat for opposite side.
Insert screws here
8.
prpd.RG-Confer 8100X-11-13_Confer 6100_12-05_R1 11/22/13 9:15 AM Page 3
er
ill
d
11.
1
C
am
tu
as
3
Separate the swing up assembly from the
ladder legs and set aside.
9.
Slide (2) two handrails up through the bot-
tom of the platform using the openings next
to the round tabs. Leave the flat ends of the
handrails exposed.
10.
2
W
po
po
do
sw
to
re
2
P
M
aw
po
to
tw
R
6.
7.
Stand the assembly up on edge and place
the tread connector over the square ends on
the (4) four treads. The large oval hole on
the tread connector must be on the same
end as the flat side on the ladder legs.
Using a rubber mallet tap the tread connec-
tor onto the square ends of the treads until
they are firmly seated. A little liquid soap on
the tread end will help.
Flip assembly over and repeat step 7 to
attach the second tread connector.
Overlap the flat end of the ladder leg onto the flat
end of the handrail. Insert one of the ¼ - 20 x 1”
bolt through the ladder leg into the handrail. Place
one of the ¼ - 20 hex nuts into the recessed area
on the handrail and tighten using a Phillips
screwdriver. Install the second nut and bolt.
14.
Attach the second ladder leg to the handrail
by repeating step #11.
12.
Stand the ladder up, using a rubber mallet tap the
platform down until seated on the lugs on the ladder
leg. IT WILL REQUIRE SEVERAL HARD BLOWS
WITH A RUBBER MALLET TO SEAT THE PLAT-
FORM ALL THE WAY DOWN ONTO LUGS.
13.
Attach the standard tread to the bottom of
the ladder as shown.
17.
Slide the (2) two adjustable tube handrails up
through the bottom of platform until seated on
the lugs.
15.
Flex the oval openings on the swing up
assembly (from step #9) over the two round
tabs on the platform. Using a rubber mallet
tap down on the tread connector until seat-
ed over the round tab. It may require sev-
eral hard hits with a rubber mallet to get
tread connector over round tabs.
16.
Using a #10 x 1-1/4” screw fasten the
upper ends of the handrails together as
shown. Repeat for opposite side.
Insert screws here
8.
prpd.RG-Confer 8100X-11-13_Confer 6100_12-05_R1 11/22/13 9:15 AM Page 3
18.
Coat the adjustable tubes with a small
amount of liquid soap and slide the
tube up through the mounting block
as shown.
4
3
If your Confer pool step is not in
the pool follow the step
instructions and place in pool.
Choose a location for your
Confer pool ladder/step
combination that is in full
view at all times. Always have
adult supervision when pool
is in use. Always swing up
outside treads and lock when
pool is not in use.
19.
Slide the asssembled tube/block
assembly up into the open end of the
adjustable tube handrail as shown.
Ladder is now ready to attach to Confer
Plastics In-Pool Step.
20.
With the step in location place your 8100x ladder over the
pool wall. Depending on the outside height of swimming
pool ledge extension boots can be removed or slid up or
down until the ladder platform is resting on top of the
swimming pool top ledge. If necessary remove or add soil
to raise or lower ladder. The 8100x ladder platform must
rest on top of the swimming pool ledge for support.
21.
With the ladder in place and platform resting on pool ledge
extend the adjustable tubes down until the mounting
blocks are resting on the top tread of pool step. Next move
the ladder in or out to position the platform mounting holes
to the outside [away from pool wall] top of pool ledge.
22.
Pool ladder must be attached to swimming pool ledge.
Mark the two positions on to the top ledge. Move the ladder
away, check to make sure the hole locations are clear of
pool wall and supports and drill two 5/16 holes through the
top ledge. Fasten the ladder platform to the top ledge using
two ¼-20 x 2-1/4” bolts, flat washers and ¼-20 hex nuts.
Repeat to attach the two step deck connectors.
23.
Using a cordless drill/driver attach the two mounting
blocks to the pool step using eight [8] #10 x 1-1/4”
screws. Secure the adjustable tubes to the adjustable
tube handrail at the pre-marked locations using two
[2] #10 x 1-1/4” screws in each handrail.
he flat
x 1”
Place
d area
7.
nd
et
t-
v-
et
Hole
Locations
prpd.RG-Confer 8100X-11-13_Confer 6100_12-05_R1 11/22/13 9:15 AM Page 4
If your Confer pool step is
not in the pool follow the step
instructions and place in pool.
Choose a location for your
Confer pool ladder/step
combination that is in full view
at all times. Always have adult
supervision when pool is
in use.
