82
83
VR2110, VR2100
VR2110, VR2100
EN
EN
1. Press the button
on the remote control to enter
the plan setting function, the Sunday symbol flashes
on the LCD.
2. Press the left and right buttons to select the day of the
week and press the button
to confirm it, then the
LCD will automatically switch to the clock setting.
3. Press the up and down buttons to set the hour and press
the left and right buttons to move to the minute setting.
Then point the remote control at the front of the robot
vacuum cleaner and press the button
to confirm
this plan setting for the robotic vacuum cleaner.
4. When one plan setting is completed, the remote
control automatically moves to the next plan setting.
If you do not want to continue with the setting, press
the exit button
or wait 10 seconds for the setting
to finish automatically.
5. This completes the time setting for both the remote
control and the robotic vacuum cleaner.
Cancelling the cleaning plan
1. Press the button
on the remote control, the
Sunday symbol flashes on the LCD and the symbols
for the days of the week you have planned appear.
2. Press the left and right buttons to select the day of the
week you have planned, and press and hold the button
for 3 seconds to cancel the plan. You can also select
the next planned day you want to cancel, or press the
exit button
or wait 10 seconds for the setting to
finish automatically.
DAILY MAINTENANCE
Main brush (clean regularly)
1. Turn the appliance over and press the latch on the
main brush cover to pull it out.
2. Remove dust from inside and from inside the main
brush with a small brush and clean the main brush.
3. Reassemble the main brush and press firmly on the
cover until the latch clicks into place.
Latch
The main
brush
Side brush
(clean regularly)
1. Turn the appliance over and pull the side brush up.
2. Remove hair and dirt and refit the side brush.
3. Make sure the left side brush (L) and right side brush
(R) correspond to the L and R symbols on the bottom
cover. Push the L and R side brushes to reinstall them.
Note: Replace the side brushes every 3 to 6 months to
ensure their cleaning effect.
R - right side
brush
L - left side
brush
Dust container and filter grid
(clean regularly)
1. Press the button and pull the dust container
backwards.
2. Open and clean the dust container.
Cleaning the filter grid
(clean regularly)
1. After prolonged use, remove the filter grid, foam filter
and HEPA filter.
2. Clean the removed filter grid. Rinse the foam filter and
HEPA filter under water.
3. Wipe the individual parts and let them dry freely.
4. After drying, gradually install them in the correct order:
grid - foam filter - HEPA filter.
Filter grid
(coarse filter)
Button
Filter cover
Foam filter
HEPA filter
Note:
•
Rinse the filter grid with clean water and do not add
any detergent.
•
Do not clean the filter grid with a brush or fingers.
•
Allow the filter grid to air dry for at least 24 hours.
•
Replace the filter grid every 3 to 6 months.
Cleaning the filter
(clean regularly)
Dust
container
HEPA filter
Foam filter
Filter grid
(coarse filter)
Water tank
Electrically operated water tank
Wiping module
(clean after each use)
1. Remove the cloth, empty the water tank.
2. Clean the cloth, dry both the water tank and the cloth.
For model VR2110, first pull out the dust container and
then empty the water tank.
Sensors
(clean regularly)
Clean the sensors with a soft cloth as follows:
1. Clean the sensors along the wall to the right.
2. Three cliff sensors at the bottom of the appliance.
3. Infra-red anti-collision sensor in front of the appliance.
4. Protection against electric shock and docking station
contacts at the bottom of the appliances (turn off the
appliance during cleaning).
5. Docking station signal transmission area.
Cliff sensor
TOF sensor
Charging
contact
Sensors
(clean every month)
Anti-collision
sensor
Infra-red
charging sensor
Base charging
contacts
Signal
transmission area
