background image

 

 

1-2

Specifications

 

 

Available NOAA Channels:

 

162.400 MHz, 162.425 MHz, 162.450 MHz, 162.475 MHz 

 

162.500 MHz, 162.525 MHz, 162.550 MHz 

 

 

Sensitivity Receive:

 

0.5 microvolts for 20 dB quieting 

 

 

Sensitivity Decoder: 

1.0 microvolts for 95% decoder accuracy

 

 

 

Image Rejection:

 -55dB 

 

 

I.F. Rejection:

 -60dB 

 

 

Modulation:

 

Narrow Band FM, 5KHz Deviation 

 

 

Antenna:

 

50 Ohm, Type BNC Connector 

 

 

L.O. Emissions:

 

Fully complaint with FCC Rules, Part 15 

 

 

Relay Closure:

 

2 Form C (DPDT) by Digital Alert Packet 

 

 

Power:

 

+12VDC @ 100 ma, DC Power Type 2.5mm 

 

 

Dimensions:

 

1.75" H x 19" W x 5" D 

 

 

Operating Temperature:

 

-15 to +55 C 

 

FCC Part 15 RF Interference

 

This device complies with part 15 of the FCC Rules.  Operation is subject to the following two 

conditions: (1) This device may not cause harmful interference, and (2) this device must accept any 

interference received, including interference that may cause undesired operation. 

 

User changes or modifications to the WX-200 not expressly approved by Computer Automation 

Technology could void the user's authority to operate the equipment. 

 

 

FCC Part 97.113.e   Prohibited transmissions.

 

No station shall retransmit programs or signals emanating from any type of radio station other 

than an amateur station, except propagation and weather forecast information intended for use by 

the general public and originated from United States Government stations. 

 

 

Summary of Contents for WX-200






















Reviews: