Computer Automation Technology CAT-300 Manual Download | Manualshive

Page: 41 / 63

background image

6-2

Audio Level Adjustment (Receiver)

The audio mixing-switching circuits of the CAT-300 are optimized around an input and output of -10dBM
(220mVAC RMS). For best results the receiver audio input should be 220mV when a DTMF tone is being received.
While providing a DTMF audio input at J3-13, adjust the RX Audio level control (R17) for an audio level at TP4 of
(220mVAC RMS).

Audio Level Adjustment (Transmitter)

Adjust the TX Audio level control (R5) for (220mVAC RMS) at TP2.

Audio Level Adjustment (Beep)

Unlock  the  CAT-300  and  enter  the  [*90]  programming  command  to  produce  the  1000Hz  test  tone.    Adjust  the
BEEP  Level  control  (R31)  for  a  transmit  audio  output  level  of  (90mVAC  RMS)  at  TP2.    Repeat  the  [*90]
programming  command  to  produce  the  test  tone.    Check  the  audio  level  at  TP1.    The  voltage  should  be
approximately (300mVAC RMS).  Exit the programming mode.

Audio Level Adjustment (Transmitter Deviation)

Once  the  RX  and  BEEP  levels  are  balanced,  adjust  the  TX  Audio  control  (R5) for the desired level of modulation
while monitoring the repeater's transmitter.  If your repeater's transmit audio input is very sensitive and you find
the  TX  Audio  level  control  is  set  to  minimum,  it  is  strongly  recommended  that  an  external  voltage  divider  be
installed at the input of the transmitter.  This will permit you to increase the TX audio output from the controller
and will insure an acceptable transmit audio signal to noise ratio.

Audio Level Adjustment (Voice Synthesizer)

Compare the receive and synthesized voice audio and adjust the VOICE Level (R35) as desired. For best quality
speech, the synthesized voice should not exceed 3KHz deviation.

Audio Level Adjustment (CW ID And Courtesy Tone)

Compare the receive and CW ID audio and adjust the BEEP Level (R31) as desired. For best results the CW ID
should not exceed 1.5KHz deviation. This will insure that repeater users will always be able to talk over the CW ID
when it comes on during a QSO in progress.

Audio Level Adjustment (Autopatch)

Access the autopatch.  With the CAT-300 in the autopatch mode, adjust the PHONE IN (R20) for the desired level
of phone audio at the transmitter.  During an autopatch the phone audio input should modulate the transmitter at
the same level as audio from the repeater's receiver.   Adjust the PHONE OUT (R18) for the desired level of receive
audio into the telephone line.

Audio Level Adjustment (Control Operator Call-in)

Call the CAT-300 on the telephone and enter the control operator mode [100#]. Interrogate the control channels
and adjust VOC PHONE OUT control (R19) for the desired voice synthesizer level.

«
...
39
40
41
42
43
...
»

Summary of Contents for CAT-300
































































Reviews:

No comments

Related manuals for CAT-300

Brand: ABATEC Pages: 8

Brand: M&C Pages: 16

Brand: XBOX Pages: 2

Brand: Samsung Pages: 27

Brand: B&G Pages: 2

Brand: B&K Pages: 9

Brand: Fancom Pages: 31

Brand: 3M Pages: 90

Brand: Gardner Denver Pages: 22

Brand: B&G Pages: 2

Brand: Samson Pages: 40

Brand: Vaillant Pages: 32

Brand: Vaillant Pages: 27

Brand: Vaillant Pages: 40

Brand: Vaillant Pages: 36

Brand: Vaillant Pages: 28

Brand: Vaillant Pages: 92

Brand: Eaton Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands