Computer Automation Technology CAT-300 Manual Download | Manualshive

Page: 22 / 63

background image

5-1

Chapter 5 - Repeater Programming By DTMF Tone

This chapter describes how the CAT-300 controller is programmed by the repeater owner using a DTMF keypad.
The various types of program commands are described in detail and examples are given in the following text.

Initialization

To initialize the CAT-300, set dipswitch #7 to ON and cycle DC power. During power-up, the voice will say:
"RESET DATA LOAD COMPLETED." Set dip-switch #7 to OFF. Initialization consists of following operations:

Dip-switch #7 Initialization

1.

All memory locations are cleared.

2.

The control channels marked with an [*] are enabled.

3.

The unlock number is loaded with the default value [1234567].

5.

The control operator prefix code is loaded with the default value [100].

6.

The control numbers are set to default values.

7.

The timers are set to default values.

8.

The voice message buffers are loaded with default messages.

9.

ID #1 is loaded with "CAT THREE HUNDRED REPEATER."

10.

ID #2 is loaded with "CAT THREE HUNDRED."

11.

All active memory saves are filled with default values.

12.

Load Hardware Input buffers with User Function Switch commands.

Programming the Unlock Control Number

To program the UNLOCK code, set dipswitch #8 to the ON position.  The voice will say: "ENTER CONTROL."  Key-
up and enter a seven-digit number.  Un-key, if the number is accepted, the voice will say: "DATA INPUTS OK."  If
the  number  is  rejected,  the  voice  will  say:  "ENTER CONTROL."  Key-up and enter the seven- digit number.  Set
dipswitch  #8  to  the  OFF  position.    NOTE:  When  the  CAT-300  is  powered  up  with  dipswitch  #7  set  to  ON,  the
unlock number defaults to: [1-2-3-4-5-6-7]

Unlocking the Controller By Radio

To unlock the controller, key-up and enter the seven digit unlock number. The voice will say: "CAT-300
CONTROL."

Locking the Controller By Radio

Key-up and send [*0]. Un-key, the controller will lock-up and the voice will say: "MANUAL EXIT." The CAT-300
will lock-up automatically when the programming timer expires. The voice will say: "TIMER EXIT." The
programming time limit can be set with the [*615*] programming command.

Programming Controller By Telephone

To program the CAT-300, call the repeater by telephone.  When the CAT-300 answers, a beep will be heard.  Enter
the seven digit unlock number followed by a (#) pound.  The voice will say: "CAT-300 CONTROL."  Programming
by phone is identical to programming by radio except you must end each entry with a [#] pound.  To terminate
programming by phone send [*0#].

NOTE:

The CAT-300 must be

unlocked

to perform the following procedures:

«
...
20
21
22
23
24
...
»

Summary of Contents for CAT-300
































































Reviews:

No comments

Related manuals for CAT-300

Brand: Panasonic Pages: 72

Brand: Panasonic Pages: 45

Brand: Panasonic Pages: 24

Brand: ABC Design Pages: 38

Brand: easydriver Pages: 26

Brand: Calsense Pages: 10

Brand: ABC Design Pages: 10

Brand: ABC Design Pages: 10

Brand: Bartec Pages: 26

Brand: Baninni Pages: 26

Brand: V2 Pages: 48

Brand: FAAC Pages: 4

Brand: FAAC Pages: 52

Brand: Rachio Pages: 2

Brand: Velleman Pages: 26

Brand: Velleman Pages: 32

Brand: Velocity Pages: 84

Brand: Watlow Pages: 59

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands