background image

can be purchased in aerosol cans 

(“spray paint”) at most hardware stores and at 

Component Playgrounds.)  
 

5. 

Plastic Lumber Platforms:

 If you have purchased a structure which includes a 

platform, the plastic lumber does not need to be finished or stained. It is 100% 
maintenance free. However, you may need to occasionally hose it down to remove dirt 
and other debris that may collect after many hours of use by happy children.  

 

6. 

Vinyl Canopies:

 If you have purchased a structure which includes a vinyl canopy, this 

product should be inspected occasionally for wear and will need to be replaced as 
necessary. Depending upon your environmental conditions, the normal life expectancy 
of the vinyl canopy is 3 

– 5 years.  

 

7. 

Swing Seats:

 These should be inspected at least twice annually and should be replaced 

as necessary.  

 

8. 

Slides: 

Slides should never be lifted at the bottom. Lifting the slide at the bottom will 

almost always cause the slide to crack at the top where it has been attached to the 
platform or bracket. Cracks and wear such as is caused by this practice are easily 
identifiable and will not be covered under the product warranty.  
 
Slides should be inspected at least annually to ensure that the sliding surface is in good 
condition. Also inspect the side rails to be sure that the plastic has not been cut or 
gouged in any manner which would present the risk of injury while sliding.  
 

9. 

Fasteners: 

All fasteners should be periodically inspected to make certain that they are 

tight and secure. Re-secure as necessary.  

 

 

 

Summary of Contents for SS38-10
















Reviews: