background image

\\Cilaklfs1\shrdata\Masters\Installation Sheets\Laser\L160SD Installation Sheet.doc 

Page 8 of 16 

9. 

Dispensing Hoses and Nozzles 

The unit may or may not be supplied with dispensing hose and nozzle assemblies.  
If customer supplied hose assemblies, pylons, reels, safe breaks and nozzles are used they must 
comply with the requirements outlined in AS/NZS 222. 
 

9.1 

Breakaways 

 
For all dispensers fitted with breakaways, ensure the breakaway is installed between the nozzle 
and the high-mast or pylon (if fitted). Any breakaways that have been subject to a break-away 
situation should be inspected and refitted or replaced in accordance with the original 
manufacturer’s instructions. 

10. 

Setting up the C4000  

 

Once the pump is connected on site, the final setup check and calibration to complete the 
installation must be carried out, using the Parameter Switch and Calibration (K-Factor) Switch. 
These switches are found on the C4000 Microprocessor Board which is housed in a metal 
enclosure located behind one of the inner column panels. 

 

10.1 

Configuration Code 

 

The configuration code has been set at Compac and should not be changed   
In the event of it being lost and having to be re-entered the configuration is written on the yellow 
label on the C4000 processor board cover. 
 

10.2 

Submersible Delay (Sd) 

  

This is the time delay from when the Submersible pump starts to when the  solenoids in the 
dispenser open to allow time for the leak detector to reset. 
This is factory set by Compac at 005 (five seconds).  
If problems are experienced with the leak detector tripping, firstly check that 'Sd' is still set and 
then, if necessary, make it longer as follows. 

 

1. Press and release the K factor switch repeatedly until 'Sd' appears on the Dollar display 
'dXXX' will appear in the litres display.  
 
2. Continue to press the K factor switch until the number to be changed flashes. Hold the switch 
down and this number will then increment. 
 
3. Release the switch when the required number is displayed. The value of the displayed number 
will then be stored in the C4000 memory as the Submersible Delay. 
 

10.3 

Parameter Switch Settings 

10.3.1 

Setting the Pump Number  

This must be set at the pump, for each hose, so that communications with  
a controller can take place. The location of this switch is shown in the  
diagram below. 
Depress the Parameter Switch nine (9) or more times until the message  

'PnA XX' 

appears in the litres display window.  When the switch is  

pressed again 

'Pnb XX 

' will appear on the display. These two options 

 will toggle each time the switch is pressed. To alter either of the pump numbers, press and hold 
the Parameter Switch when the pump number to be altered appears on the display. This number 
will then increment. The switch should be released when the desired pump number is displayed. 
The value of the displayed number will then be stored in the C4000 memory as the pump 
number for that hose. 

NOTE

: For a single hose only 

‘Pn”

 will appear 

Summary of Contents for L160SD

















Reviews: