Compac ComTank Installation Sheet Download Page 14

Powering up 

Modem Connections 

 

Compac Industries Ltd. 

Page 14 

www.compac.co.nz 

 

Powering up  

 

When all connections have been made and checked. Install the protective perspex 
cover over the terminals. 

 Where regulations require, a registered electrician must check and 

approve connections. 

 

Connect power to the unit and turn on the circuit breaker. 

Check that the PIN pad screen (if fitted) is illuminated and boots up. 

 

If the unit is controlled via the internet, contact your help desk and confirm that the 
unit is on line. Confirm the on-line pump pricing. 

 

Checking Pump Prices 

 

The following is a brief overview for technicians who are experienced in the 
installation and setup of similar equipment. Specific instructions for each option are 
either supplied or available from Compac. 

The ComTank unit controls the pricing at the pumps. In most circumstances the 
pricing information is sent to the unit either via a USB key or via the internet using 
Netbase or CompacOnline.  

Pricing via USB Module 

 

 

Start up your laptop, insert the Compac USB key and open the Price file. Check the 
price is correct. If not, change it and save. 

Insert the key into the USB module, select Set Price and confirm. 

Turn off the unit and the pumps, connect the pump communications wires and 
repower. 

Check that the pricing on each hose is correct. 

Pricing via Internet 

 

 

Confirm that the unit is on line and that the help desk has installed all updates. 

Write down the on-line price(s). 

Turn off the unit and the pumps, connect the pump communications wires and 
repower. 

Check that the price on each hose matches the on-line price. 

 

 

Summary of Contents for ComTank



















Reviews: