Comnet NetWave NW7 Installation And Operation Manual Download Page 26 | Manualshive

Page: 26 / 70

background image

INS_NW7[E]_REV– 06/10/13 PAGE 26

INSTALLATION AND OPERATION MANUAL

NW7[E]

TECH SUPPORT: 1.888.678.9427

10.0 System Tab

Within the System >>System page, you can configure the device parameters such as the
hostname, time zone and set Time Synchronization.

Figure 19: The System top-level tab.

10.1 System Properties

Within the section on System Properties, there are tabs corresponding to General Settings,
Logging, and Language and Style.

General Settings

Local Time

Displays the local time according to the time zone.

Hostname

Configures the name of the device.

Time Zone

Sets the time zone.

«
...
24
25
26
27
28
...
»

Summary of Contents for NetWave NW7







































































Reviews:

No comments

Related manuals for NetWave NW7

Brand: rainforest Pages: 20

Brand: BAB TECHNOLOGIE Pages: 52

Brand: UfiSpace Pages: 14

KNX-GSM Gateway

Brand: B+B Pages: 19

Brand: Epygi Pages: 55

Brand: Badger Meter Pages: 24

NetLink Wireless Telephone

Brand: SpectraLink Pages: 30

Brand: Aaeon Pages: 20

Brand: Gigaset Pages: 8

Brand: QEI Pages: 43

Brand: QEI Pages: 48

Brand: QEI Pages: 45

VMG1312-B Series

Brand: ZyXEL Communications Pages: 376

Brand: Cooper Bussmann Pages: 115

Brand: RTA Pages: 74

Brand: RTA Pages: 81

AC-4CM10-650-F-20-000

Brand: Janus Pages: 8

Brand: Videx Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands