Comnet NetWave NW7 Installation And Operation Manual Download Page 35 | Manualshive

Page: 35 / 70

background image

INS_NW7[E]_REV– 06/10/13 PAGE 35

INSTALLATION AND OPERATION MANUAL

NW7[E]

TECH SUPPORT: 1.888.678.9427

11.0 Network Tab

You can view and configure the interfaces of the local area network (LAN) zone as well as the wide
area network (WAN) zone. Network address translation (NAT) occurs between these two network
zones. The router that performs the NAT is called a gateway. A gateway is a network point that
acts as an entrance to another network.

Figure 32: The Network top-level tab.

Figure 33: The Interface Overview on the Network » Interfaces page.

The Network column shows that the WAN zone has the physical port “eth1” as its interface.

In Figure 33, the LAN zone (icon with two Ethernet ports) has the bridged interface “br-lan” which
consists of one physical port (icon with one Ethernet port) and two wireless networks (each icon
looking like a short standing fan) on the device. Hovering the mouse over each icon would give
the name of the interface it represents.

«
...
33
34
35
36
37
...
»

Summary of Contents for NetWave NW7







































































Reviews:

No comments

Related manuals for NetWave NW7

Brand: ICP DAS USA Pages: 96

Brand: ICP DAS USA Pages: 38

Brand: ICP DAS USA Pages: 17

Brand: ICP DAS USA Pages: 4

Brand: ICP DAS USA Pages: 8

Brand: Farfisa Pages: 12

ServiceRouter V2

Brand: Eurogard Pages: 23

Brand: Echelon Pages: 3

Brand: NETGEAR Pages: 163

NetComm CloudMesh NL19MESH

Brand: Casa Systems Pages: 3

Brand: Acer Pages: 113

Dynalite DTK622-USB

Brand: Philips Pages: 2

Dynalite DMNG232

Brand: Philips Pages: 2

Dynalite DDNI-LON

Brand: Philips Pages: 2

Dynalite DDNG485

Brand: Philips Pages: 2

Dynalite DDNG232

Brand: Philips Pages: 2

Dynalite DDNG100BT

Brand: Philips Pages: 2

Dynalite DDNG-KNX

Brand: Philips Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands