Page 12
R.5-MAX, R2-MAX
Installation and Operation Manual
R2-64 MAX
R2-66 MAX
R2-94 MAX
SYSTEM
TRANSDUCERS
LF:
MF:
HF:
2 x 12" inherently weather-resistant cones with 3" voice coil, neodymium motor and aluminum demodulation ring
1 x 2" exit, M200HP compression, 3.5" diaphragm, 2.2" Voice coil, high temp non-metallic diaphragm
1 x 1.4" exit compression, 2.87" voice coil, copper shorting ring, titanium diaphragm with mylar surround
Operating Mode:
Biamp (Passive MF/HF)
Operating Range
1
:
70 Hz to 22
kHz (-10 dB)
70 Hz to 22
kHz (-10 dB)
70 Hz to 22
kHz (-10 dB)
Frequency Response
1
:
85 Hz to 18 kHz (-3 dB)
85 Hz to 20 kHz (-3 dB)
85 Hz to 20 kHz (-3 dB)
Nominal Beamwidth (-6dB):
60° x 40°, 1.6 kHz to 10 kHz
60° x 60°, 1.6 kHz to 10 kHz
90° x 40°, 1.6 kHz to 10 kHz
Axial Q / DI:
24.89/13.96, 1.6 kHz to 10 kHz
17.13/12.34, 1.6 kHz to 10 kHz
14.75/11.69, 1.6 kHz to 10 kHz
Maximum Output
2
without EQ
3
:
with EQ
4
:
133 dB (139 dB Peak)
132 dB (138 dB Peak)
133 dB (139 dB Peak)
132 dB (137 dB Peak)
132 dB (137 dB Peak)
131 dB (136 dB Peak)
Crossovers
5
LF:
MF:
Passive MF/HF:
4
th
order (24 dB/oct) 450 Hz, Active
8
th
order (48 dB/oct) 450 Hz, Active
8
th
order (48 dB/oct) 3.3 kHz
Recommended Processing
6
:
DSP with CONEQ™ power response correction
PERFORMANCE
Maximum Input Ratings
LF:
MF/HF:
1200W Continuous (98V) / 4800W Peak (196V)
150W Continuous (35V) / 300W Peak (70V)
Sensitivity
7
LF:
MF/HF:
103 dB (100 Hz - 500 Hz)
108
dB (400 Hz - 18 kHz)
103 dB (100 Hz - 500 Hz)
108
dB (400 Hz - 18 kHz)
103 dB (100 Hz - 500 Hz)
107
dB (400 Hz - 18 kHz)
Maximum Output
8
(without EQ)
3
LF:
MF/HF:
(with EQ)
4
LF:
MF/HF:
134 dB (140 dB peak)
130 dB (136 dB peak)
133 dB (139 dB peak)
129 dB (135 dB peak)
134 dB (140 dB peak)
130 dB (136 dB peak)
133 dB (139 dB peak)
129 dB (135 dB peak)
134 dB (140 dB peak)
129 dB (135 dB peak)
133 dB (139 dB peak)
128 dB (134 dB peak)
Nominal Impedance
LF:
MF/HF:
8 ohms, (9.3 ohms @ 250 Hz minimum)
8 ohms, (5.6 ohms @ 5 kHz minimum)
SYSTEM
Input Connection:
2 x 12' (3.6 m) 16-2 SJOW cables
Enclosure:
Hand-laminated multilayer fiberglass
Finish:
Paintable, light grey gel-coat
(RAL #7038)
Rigging Provisions:
(5) 1/2"-13 rigging points; Steel zinc-rich epoxy dual-layer powder-coated bracket;
(2) Aluminum aiming straps to secure angle
Grille:
3-layer Weather-Stop™ with polyester mesh, foam, and zinc-rich epoxy dual-layer powder-coated
perforated steel, color-matched to enclosure
Environmental:
IEC529 IP55W rating with a minimum 5° down-tilt,
Designed to MIL-STD-810G
Dimensions – H x W x D:
24.75" x 24.75" x 30.75" (629 x 629 x 781 mm)
Loudspeaker Unit Weight:
92 lbs (42.2 kg) loudspeaker only, 115 lbs (52.2 kg) with yoke bracket
1. Operating range and frequency response parameters are stated with DSP equalization applied.
2. Calculated algebraic sum of LF and passive MF/HF with recommended active crossover based on power rating and sensitivity, exclusive of power compression.
3. Raw driver or system response prior to applying any filters for frequency response or power response correction.
4. Recommended equalization as published in the Community Loudspeaker Library within Community's Resyn™ software.
5. Resultant engineered acoustical response of crossover network and components.
6. Community's dSPEC226 loudspeaker signal processor DSP and Resyn™ software include CONEQ™ 1000 point FIR filter power response correction filters within the
preconfigured speaker file for this model of loudspeaker.
7. Free field anechoic sensitivity, calculated using input voltage that would produce 1W at the nominal impedance.
8. Calculated based on power rating and sensitivity, exclusive of power compression.
SPECIFICATIONS