R.5-MAX, R2-MAX
Page 11
Installation and Operation Manual
SPECIFICATIONS
Community strives to improve its products on a continual basis. Specifications are therefore subject to change without notice.
R.5-66 MAX
R.5-96 MAX
Loudspeaker Type:
2 way, full-range, coaxial
2 way, full-range, coaxial
Driver Complement:
LF: 1 x 12" with neodymium motor and
aluminum demodulation ring
HF: 1 x 1.4" exit compression driver
with 2.87" voice coil
LF: 1 x 12" with neodymium motor and
aluminum demodulation ring
HF: 1 x 1.4" exit compression driver
with 2.87" voice coil
Operating Range
1
:
70 Hz to 20 kHz (-10 dB)
70 Hz to 20 kHz (-10 dB)
Frequency Response
1
:
95 Hz to 19 kHz (-3 dB)
95 Hz to 20 kHz (-3 dB)
Max Input Ratings:
600W RMS, 1200W Program
69 volts RMS, 138 volts momentary peak
600W RMS, 1200W Program
69 volts RMS, 138 volts momentary peak
Maximum Output
2
without EQ
3
:
with EQ
4
:
131 dB (137 dB Peak)
130 dB (136 dB Peak)
130 dB (136 dB Peak)
129 dB (135 dB Peak)
Sensitivity (1W / 1m)
Free Space SPL
3,5
:
103 dB (125 Hz - 10 kHz)
103 dB (250 Hz - 4 kHz)
102 dB (125 Hz - 10 kHz)
103 dB (250 Hz - 4 kHz)
Nominal Impedance:
8 ohms, 4.8 ohms @ 200 Hz minimum
8 ohms, 4.8 ohms @ 200 Hz minimum
Nominal Beamwidth (-6dB):
60° x 60°, 1.6 kHz to 10 kHz
90° x 60°, 1.6 kHz to 10 kHz
Axial Q / DI:
18.7/12.7, 1.6 kHz to 10 kHz
13.8/11.4, 1.6 kHz to 10 kHz
Crossover Frequency:
900 Hz
Recommended
Processing
6
:
DSP with CONEQ™ power response correction
Recommended Amplifier:
1200W to 1800W at 8 ohms
Input Connection:
12 foot (3.6m) SJOW #16-2 cable
Controls:
None
Rigging Provisions:
Five 3/8"-16 rigging points, Zinc-rich epoxy dual-layer powder-coated yoke
Construction:
Rotomolded LLDPE plastic
Finish:
Black, White or Light Grey (RAL# 9004, 9003, 7038)
Grille:
3-layer Weather-Stop™ with polyester mesh, foam, zinc-rich epoxy dual-layer powder-coated
perforated steel color-matched to enclosure
Environmental:
IP55W per IEC 529 at 5° down-tilt, Designed to MIL-STD-810G
Dimensions H x W x D:
16" x 16" x 16.19" (406 x 406 x 411 mm)
Net weight:
44 lbs (20 kg) loudspeaker only, 47 lbs (21.3 kg) with yoke bracket
1. Operating range and frequency response parameters are stated with DSP equalization applied.
2. Calculated based on power rating and sensitivity, exclusive of power compression.
3. Raw driver or system response prior to applying any filters for frequency response or power response correction.
4. Recommended equalization as published in the Community Loudspeaker Library within Community's Resyn™ software.
5. Free field anechoic sensitivity, calculated using input voltage that would produce 1W at the nominal impedance.
6. Community's dSPEC226 loudspeaker signal processor DSP and Resyn™ software include CONEQ™ 1000 point FIR filter power response correction filters within the
preconfigured speaker file for this model of loudspeaker.
Note:
Every effort has been made to insure that the information contained in this manual was complete and accurate at the time of printing.
However, due to ongoing technical advances, changes or modifications may have occurred that are not covered in this manual. Visit
Community at http://www.communitypro.com for the latest version of this manual and the most recent product information.