manualshive.com logo in svg

Community ENTASYS 200, Installation & Operation Manual, Page: 7 / 28

Share
Download
Community ENTASYS 200 Installation & Operation Manual Download Page 7

 ENTASYS 200 Installation/Operation Manual — Page 7  

 

IMPORTANT SAFETY INFORMATION 

Always follow these safety precautions when using or installing ENTASYS 200 loudspeakers and 
accessories: 



Read and keep these instructions. 



Heed all warnings. 



Follow all instructions, particularly those pertaining to rigging, mounting, hanging, and 
electrical connections. 



Only use accessories that are specified and approved by Community.  

 

The terms IMPORTANT,  WARNING, and DANGER, as used in this manual, alert the reader to 
important safety considerations. If you have any questions or do not understand the meaning of 
these terms, do not proceed with installation. Contact your local dealer, distributor, or call 
Community directly for assistance.  

IMPORTANT: 

describes an operating condition or user action that may expose the equipment or user 

to potential damage or danger.  

 

WARNING:

 describes an operating condition or user action that will likely cause damage to the 

equipment or injury to the user or to others in the vicinity.  

 

DANGER:

 describes an operating condition or user action that will immediately damage the equipment 

and/or be extremely dangerous or life threatening to the user or to others in the vicinity. 

 

RIGGING AND ELECTRICAL SAFETY 

 

DANGER: 

The loudspeakers described in this manual are designed and intended to be mounted using a 

variety of rigging hardware, means and methods. Installation of loudspeakers should only be 
performed by trained and qualified personnel. It is strongly recommended that a licensed and certified 
professional structural engineer approve the mounting plan. Severe injury and/or loss of life may 
occur if these products are improperly installed!  

 

DANGER

: 

All rigging fittings must be fully tightened and secured. Any missing fasteners will 

compromise the structural integrity of the enclosure and constitute a safety hazard. Do not 
suspend this loudspeaker unless all fasteners are securely in place! 

 

IMPORTANT

: Refer to the sections on installation and connections later in this manual for additional 

information on rigging and electrical safety. 

 

DANGER

: It is possible to experience severe electrical shock from a power amplifier. Always make 

sure that all power amplifiers are in the “OFF” position and unplugged from an AC Mains supply 
before performing electrical work. 

 

 

 

Important Safety information 

Summary of Contents for ENTASYS 200





























Reviews:

No comments