manualshive.com logo in svg

CommScope SYSTIMAX EHD, User Manual

Share
Download
CommScope SYSTIMAX EHD User Manual Download Page 17

TECP-91-005 • Issue 5 • October 2017

Page 17

© 2017

CommScope

. All Rights Reserved.

5

GENERAL CABLE REQUIREMENTS

Pre-terminated SYSTIMAX EHD Panels use RBR G657.A1 reduced-bend-radius 
singlemode fiber.   Installers need to follow the manufacturer recommended settings 
when testing and splicing the RBR G657.A1 fiber to the G.652 standard singlemode 
fiber.   Please alert contractors to this fact. 

The minimum cable bend radius is 10 inches (25.4 cm). 

CommScope recommends the following type patch cords for use in the SYSTIMAX 
EHD Panel: 

• 2-Fiber UPC LC Singlemode Dual-Zip 1.7mm patch cord FPCT-SPLC-S-xM

• 2-Fiber UPC LC Singlemode Dual-Zip 1.7mm RBR patch cord FPCTE-SPLC-S-

xM

• 2-Fiber UPC LC Singlemode Dual-Zip 2mm patch cord FPC2-SPLC-S-xM

• 2-Fiber UPC LC Singlemode Dual-Zip LSZH 2mm patch cord FPCH2-SPLC-S-xM

• 2-Fiber UPC Duplex LC Singlemode Dual-Zip 1.7mm patch cord FPCT-SDLC-S-

xM

• 2-Fiber UPC Duplex LC Singlemode Dual-Zip 1.7mm RBR patch cord FPCTE-

SDLC-S-xM

• 2-Fiber UPC Duplex LC Singlemode Dual-Zip 2mm patch cord FPC2-SDLC-S-xM

• 1-Fiber UPC LC Singlemode 1.7mm patch cord FPCF-SPLC-S-xM

• 1-Fiber UPC LC Singlemode 2mm patch cord FPCM-SPLC-S-xM

The maximum patch cord size that can fit in the panel is 2mm simplex or duplex.

Summary of Contents for SYSTIMAX EHD























Reviews:

No comments

Brands by name

Popular brands

Load more brands