manualshive.com logo in svg

CommScope Node AM4, Manual

Share
Download
CommScope Node AM4 Manual Download Page 78

 

7. Specifications

 

Page 78 

   

MF0121ACP

_uc.docx

                      Manual for Node AM4 

 

7.5. Modems 

7.5.1. HC25 / PHS8 / PLS8 / MC88 / TRM-5 

MC Technologies MC88 / TRM-5

 

Service GSM/GPRS 

Service connection 

Circuit switch 

Packet switch

Physical connection 

RS232, 6PG Molex, FME 

Power consumption 

4 W 

Connectors 

Data, power, RF 

MC Technologies HC25

1)

 / PHS8

1)

 / PLS8-EU / PLS8-US

 

Service HC25 /  
PHS8 

GSM/GPRS/EDGE/UMTS HSPA

2)

 

GPS

Service

 

PLS8EU

 

LTE: 800/900/1800/2600 MHz, FDD-Band (20,8,3,7)  
UMTS (WCDMA): 900/1800/2100 MHz, FDD-Band (8,3,1) 
GSM/GPRS/EDGE: 900/1800 MHz 
GPS 

Service

 

PLS8US

 

LTE: 700/850/AWS(1700/2100)/1900 MHz, FDD-Band (17,5,4,2)  
UMTS (WCDMA): 850/AWS(1700/2100)/1900 MHz, FDD-Band (5,4,2) 
GSM/GRPS/EDGE: 850/900/1800/1900 MHz 
GPS 

Service connection 

Circuit switched data (not available for PLS8) 

Packet switched data 

Physical connection 

USB, RS232

3)

, 6PG Molex, FME 

Power consumption 

4 W

Connectors 

Data, power, RF

1)

 

Modem PHS8 is replacing Modem HC25, which is discontinued (both are identical except the fact that 
the RS232 connector must not be used with the PHS8 type).  

2)

  HSPA is for PHS8 only 

3)

 

The RS232 connector must not be used with the PHS8 and PLS8 types.  

 

Note: 

The HC25 / PHS8 and MC88 modems are similar. 

For TRM-5 and MC88 

modems, please make sure that the serial port baud rate is set to the appropriate 
value. 

Please refer to the Node AM/ Node A+ Software Manual for more details.  

 

7.5.2. Wireless Router M!DGE (Racom) 

M!DGE *

Service LTE/HSPA/UMTS/EDGE/GPRS 

Service connection 

Circuit switch 

Packet switch

Physical connection 

RS232, 2x Ethernet, USB, SMA 

Power consumption 

5 W 

Connectors  

Data, power, RF 

* 

M!DGE Wireless Router supported by software, mounting kit incl. cables available;  

 

M!DGE router must be purchased directly at Racom or any distributors. 

Summary of Contents for Node AM4




















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands