manualshive.com logo in svg

CommScope Node AM4, Manual

Share
Download
CommScope Node AM4 Manual Download Page 47

4. Functional Description 

 

MF0121ACP

_uc.docx   

      

 Manual for Node AM4 

Page 47

 

 
 

  

 

 

figure 4-17 Position of UI2 Board and BBU 

 Note: 

We recommend replacing the battery pack 

after 4 years

 of operation. 

1. 

Caution

: Electrolyte inside. Risk of health hazards associated with electrolyte leakage. 

Do not disassemble, puncture, modify, drop, throw, or cause other unnecessary shocks 
to batteries. 

2. 

Caution

: High current if shorted. Risk of injury by high current. Do not short circuit the 

batteries.  

3. 

Caution: 

The batteries might be hot. Risk of burns by hot surface. Do not touch the 

batteries before they have sufficiently cooled down. 

Notice:

 For the replacement procedure, also observe the health and safety warnings 

in chapters 

5.1

 and 

5.2.1

 as well as the notes in chapter 

5.2

.  

Do not put the batteries to the garbage but dispose of them properly according local 
and/or regional regulations. 

To 

replace the battery pack,

 first uninstall the multiband combiner as explained in 

chapter 

5.2.1

. Then, proceed as follows: 

  Unplug the complete module on which the battery pack is installed. Disconnect the 

battery cable at the UI2 board. 

 Just 

loosen

 the M3x16 hexagon socket-head-cap screw on top of the cover of the 

battery pack. It is not necessary to unscrew this screw entirely! 

  Then the battery pack can be removed easily. 

  Insert the new battery pack and fasten the M3x16 hexagon socket-head-cap screw 

again. 

  Reconnect the DC connector to the "Battery" connector at the UI2 board. 

BBU 

cover sheet 

Battery pack 

underneath 

UI2 board 

Hexagon 
socket-head- 
cap screw 

Battery connector 

USB connector 

Ethernet 

connector 

VSWR module (optional) 

Modem 

(optional) 

USB connectors 

Summary of Contents for Node AM4




















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands