manualshive.com logo in svg

CommScope Node AM4, Manual

Share
Download
CommScope Node AM4 Manual Download Page 58

 

5. Maintenance

 

Page 58 

   

MF0121ACP

_uc.docx

                      Manual for Node AM4 

 

The long hole of the combiner’s carrier plate is hooked into a screw of the modem 
mounting plate, so both plates will be pulled out together: 

 

 

 

Unhook the plates and disconnect 

all

 cables from the combiner. 

Remember their positions for later 
reconnection. 

 

Then, also carefully pull out the modem carrier 
plate completely, as well.  

 

For battery replacement, please refer to chapter 

4.3.6

 

Fehler! Verweisquelle konnte 

nicht gefunden werden.

. 

To replace the modem, proceed as follows: 

Carefully disconnect all cables from the 
modem and remember their positions for 
reconnection. 

 

Note:

 In some cases, a cable tie (as 

illustrated to the right) might be used. 
Cutting this cable tie is not necessary if 
you proceed exactly in the order as 
described in the following 
 

 

 

Mounting plates of combiner and modem connected by 
screw locked into long hole (seen from both sides). 

Cable tie 

exemplary 

Summary of Contents for Node AM4




















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands