manualshive.com logo in svg

CommScope ION-U EU H 23/23, User Manual

Share
Download
CommScope ION-U EU H 23/23 User Manual Download Page 23

4. Commissioning 

 

 

M0200ABA_ION-U_EU_H

_23_23

  User’s Manual for ION

®

-U 

Page 23 

 

4.3.  Electrical Installation 

4.3.1.  Health and Safety for electrical installation 

 
Read and observe the notices in chapter 1.2 Health and Safety. 
 

1.  Danger: Electrical hazard. Danger of death or fatal injury from electrical 

current. Obey all general and regional installation and safety regulations 
relating to work on high voltage installations, as well as regulations 
covering correct use of tools and personal protective equipment. 

4.3.2.  Property Damage Warnings for electrical installation 

1. 

Attention:

  It is compulsory to ground (earth) the unit before connecting the 

power supply. A grounding bolt is provided on the cabinet to connect the ground-
bonding cable. 

2. 

Attention: 

If the mains connector of the Extension Unit is not easily accessible, a 

disconnect device in the mains power circuit must be provided within easy reach. 

3. 

Attention:

  A connection of the mains supply to a power socket requires the 

power socket to be nearby the Extension Unit. 

4. 

Attention: 

Before connecting or disconnecting the mains connector at the 

Extension Unit, ensure that mains power supply is disconnected. 

5. 

Attention: 

Make sure that an appropriate circuit breaker acting as a disconnect 

device (as required by IEC/EN60950-1) and an overcurrent limiting device are 
connected between mains power and the Extension Unit. 

6. 

Attention:

  Incorrectly wired 

connections

  can destroy electrical and electronic 

components. 

7. 

Notice:

 Although the Extension Unit is internally protected against overvoltage, it 

is strongly recommended to ground (earth) the antenna  cables close to the 
antenna connectors of the Extension  Unit for protection against atmospheric 
discharge. In areas with strong lightning, it is strongly recommended to install 
additional lightning protection. 

8. 

Notice:

  To avoid corrosion at the connectors caused by electrochemical 

processes, the material of the cable connectors must not cause a higher potential 
difference than 0.6 V (see electrochemical contact series). 

 

 

Summary of Contents for ION-U EU H 23/23


















































Reviews:

No comments

Brands by name

Popular brands

Load more brands