CommScope ADCP-90-326 User Manual Download

Page: 5 / 26

ADCP-90-326 • Rev B • November 2020

Page 5

•

Sliding Adapters Packs

—Each with two adapters, provide easy access for connecting

cables and cleaning connectors. Product offerings for adapters/connectors include most
industry-standard multimode and singlemode types.

Figure 2

shows a closed tray with the sliding radius limiter in a closed position. Also shown is

the optional lock.

Figure 2. FMT Features (Closed Tray Shown)

2 SPECIFICATIONS

Table 1

lists specifications for the Fiber Management Tray.

Figure 3

shows the FMT dimensions

for rack type, rack width, and recess options.

Table 1. Fiber Management Tray Specifications

ITEM

DESCRIPTION

Dimensions (H

See

Figure 3

page 6

Approximate Weight

7.9 lbs. (3.98 Kg)

Configuration Options

and Capacity

Termination/storage (12, 16, or 24 terminations)
Bulk storage

3 mm O.D. cable: 32 cables, length 1.7 m (66 in.) each
2 mm O.D. cable: 48 cables, length 3.4 m each (132 in.)
1.7 mm O.D. cable: 60 cables, length 3.9 m (154 in.) each

Termination and splice (12 splices)

LOCK

(OPTIONAL)

MOUNTING BRACKET

(ONE EACH

IDE)

202

2-A

LIDING RADIU

LIMITER

(ONE EACH

IDE)

Summary of Contents for ADCP-90-326



























Search results

Summary of Contents for ADCP-90-326

Reviews:

Related manuals for ADCP-90-326

Brands by name

Popular brands

CommScope ADCP-90-326, User Manual

Search results

Summary of Contents for ADCP-90-326

Reviews:

Related manuals for ADCP-90-326

Brands by name

Popular brands