CommScope ADCP-90-326 User Manual Download Page 4

Page: 4 / 26

ADCP-90-326 • Rev B • November 2020

Page 4

Figure 1

shows one of the FMT configurations, the 12-position termination and storage tray.

Some of the features common to all FMT configurations are displayed.

Figure 1. FMT Features (12-Position Termination and Storage Tray, Universal Entry, Shown)

The features shown include the following (from bottom left clockwise):

•

Edge Protectors

—Protect cables from sharp angles at bend points.

•

Release Tabs

—Allows the FMT tray to open.

•

Lock Open Latch

—Allows the technician to lock open the FMT while working in the tray.

•

Rear Radius Limiters (Left and Right)

—Maintain a protective, minimum-bend radius

for cables routed into panel.

•

Tie Lances

—Provide anchor points for securing fibers.

•

Storage Radius Limiters

—Provide service loop storage for cable terminated in panel.

•

Mounting Brackets

—Adapt the tray for the different mounting options. Brackets may by

mounted in several recess locations based on customer needs.

•

Sliding Radius Limiter

—Provides protective entry point for cables. Radius limiter slides

backward when tray is pulled out and forward when tray is closed.

LEFT REAR

RADIUS LIMITERS

LOCK OPEN

LATCH

RIGHT REAR

RADIUS LIMITERS

EDGE

PROTECTORS
(4 EACH SIDE)

SLIDING

ADAPTER

PACKS

STORAGE

RADIUS

LIMITERS

MOUNTING

BRACKET

(2 PLACES)

SLIDING RADIUS

LIMITER (2 PLACES)

20198-A

TIE LANCES

(EACH SIDE)

RELEASE

TAB

RELEASE

TAB

Summary of Contents for ADCP-90-326



























Search results

Summary of Contents for ADCP-90-326

Reviews:

Related manuals for ADCP-90-326

Brands by name

Popular brands

CommScope ADCP-90-326, User Manual

Search results

Summary of Contents for ADCP-90-326

Reviews:

Related manuals for ADCP-90-326

Brands by name

Popular brands