9
User manual CIBS Office 1g
NO
EN
NO
EN
10
User manual CIBS Office 1g
NO
EN
NO
EN
Configuration of microphone sensitivity (loudness of your voice)
Use a pen or similar pointed object to press and hold button
16
d, while
adjusting the sensitivity up or down by pushing button
16
a or
16
b.
The light bar
16
c indicated the level of microphone sensitivity.
Switch Blues II on/off
How to switch the Blues II on:
Press and hold the On/off button
•
7
until you see the
Battery indicator lamp
6
turn blue. Simultaneously you will hear a
signal via the T-Loop or via connected headphones/earbuds.
How to switch the Blues II off:
Press and hold the On/off button
•
7
until you see the Battery
indicator lamp
6
turn red. Simultaneously you will hear a signal
via the T-Loop or via connected headphones/earbuds.
Pairing the units
The units must be programmed to be able to communicate, with each
other. This is done by connecting these together wirelessly (pairing).
NOTE! It is important that Blues II and Tango VII are within a distance of
less than 1 meter during pairing and that Blues II are fully charged.
Pair Blues II with the Tango VII
Press and hold the pairing button
•
9
until the Battery indicator
light
6
flashes alternately red and blue and you hear a double
tone.
The Blues II is now ready to pair for approximately 3 minutes.
•
Press and hold the Tango VII’s pairing button
•
14
e
until the
communication light
18
flashes alternately red and blue.
The Tango VII is now ready to pair.
•
When Blues II and Tango VII are paired together the communi-
•
cation light
18
will light stable blue.
If the pairing was unsuccessful, repeat the procedure.
•
Find the cable that connects the telephone receiver to the desk
1.
phone. Detach it from the desk phone and connect it to the input for
telephone receiver on the Tango VII
19
Then, connect the accompanied cable (60cm) to the desk phone
2.
where the above cable was detached (1), and to the input for desk
phone on Tango VII
20
.
Handset lifter (accessory) can be connected to the input for handset
3.
lifter
21
.
Configuration Tango VII
Configuration means adapting the Tango VII to your desk phone.
See the Configuration list on the last page.
If your desk phone is listed on the attached Configuration list, apply the
configuration digit that corresponds with your phone, and continue to
alternative a.
If your desk phone is not listed, continue to alternative b.
Alternative a.
Use a pen or similar pointed object to press and hold configuration
button
14
d. The configuration number is indicated by a light in the
indicator bar
14
c, with configuration number 01 at the bottom and 08 at
the top. Press
14
a or
14
b repeatedly to select the configuration digit of
your phone. When the correct digit is selected, release the button
14
d.
Make sure that you can hear the dialling tone in your phone and check
the microphone by blowing on it. Tango VII is now successfully confi-
gured.
Alternative b.
Press button
11
to activate the telephone receiver. Use a pen or similar
pointed object to press and hold configuration button
14
d.
The configuration number is indicated by a light in the indicator bar
14
c,
with configuration number 01 at the bottom and 08 at the top.
Lift the telephone handset and press
14
a or
14
b repeatedly until you hear
the dialling tone clearly through the receiver. Check that the microphone
works by blowing on it. If not, step to the next configuration number and
repeat the microphone test. When you both hear the dialling tone and the
microphone works, your Tango VII is successfully configured.
The configuration button
14
d can then be released.
If too much time elapses, the dialling tone will cease and you must
replace the handset and lift it again in order to continue configuration.
