CommBox CFP700 Instruction Manual Download Page 10

Page: 10 / 10

Step 16:

Cover plates

437, Push up and bend
the LED control panel
bracket for clearance for
part 437

Using 4x 6x12mm cap
screws two per side
secure parts 437 to the
rear of parts 969 and 971
as shown.

Cycle the trolley Up/Down including tilting to table to ensure nothing
fowls on any of the moving parts during the travel cycles.

Transportation:

Please ensure the

panel is lowered to it’s lowest point prior to any

movement.

Warning:

he rear castor brakes are only to be used during the transportation faze.

Always leave the castors unlocked for normal classroom use.

Bolt Pack:

4x8mm

Screw

x 6

4x12mm

Screw

x 3

4mm

Nylock Nuts

x 9

6x12mm

Socket Head Screw

x 31

6mm

Nylock Nut

x 11

6mm

Washer Small

x 4

8x12mm

Bolt

x 8

8x20mm

Bolt

x 4

8x65mm

Cup Head Bolt

x 4

8mm

Nylock Nut

x 12

10x20mm

Bolt

x 2

10mm

Washer

x 4

10mm

Nylock Nut

x 2

12x30mm

Bolt

x 4

12mm

Nylock Nut

x 4

Summary of Contents for CFP700











Search results

Summary of Contents for CFP700

Reviews:

Related manuals for CFP700

Brands by name

Popular brands

CommBox CFP700, Instruction Manual

Search results

Summary of Contents for CFP700

Reviews:

Related manuals for CFP700

Brands by name

Popular brands