background image

  1 

 

 

 

 

 

 

 

 

                                       

PS2000AN Operator’s Guide

 

Unpacking the PS2000AN 

 

When you open the PS2000AN box for the first time, inspect the contents. In the box, you should find the following 
items: 

 

 
If any of these items are missing or damaged, contact the dealer where you purchased the unit, or call Customer 
Service at the number listed in "Service Information." 

 

Installing the PS2000AN

   

 

Positioning the PS2000AN 

You can operate the PS2000AN from a flat surface 
such as a table, counter, or shelf. Or, you can use the 
supplied wall-mount brackets to mount it on a wall. 
Steel and concrete walls reduce transmitting range. If 
the PS2000AN is located in a concrete or steel 
building, and part of the coverage area is located 
outside the structure, place the unit and antenna close 
to a window. 
To mount the PS2000AN on a wall, perform the 
following steps: 
 

1.

 Slide the wall-mount brackets into the 2 wall-mount 

slots, as shown. 

 

 

 
                                                        Back of the   
                            PS2000AN 

 
 

 

2. 

Insert the center-loaded antenna connector into the 

ANTENNA

 jack on the PS2000AN. Turn the 

connector clockwise until the antenna locks in 
place. For maximum efficiency, extend the antenna 
to its full length, orient it vertically, and avoid 
contact with walls and metal objects. 

 

 

3. 

Mark the positions for the 2 supplied mounting 

screws on the wall. The positions should be 6" 
apart. Drill the 2 holes, then thread the screws into 
the wall. The screws should extend 3/16". Do not 
over tighten the screws. 

 

4. 

Align the keyholes on the back of the brackets with 

the 2 screws, then push in and press down to secure 
the PS2000AN to the wall. 

 

 

 
For best transmission, both the center-loaded antenna 
and the black antenna ground wire must be fully 
extended. Do not coil the antenna ground wire, as this 
will decrease transmission efficiency. 
 

  Back of the 
  PS2000AN 

 

 
 
 

 

Summary of Contents for PrivatePage PS2000AN
















Reviews: