Comm-Tec UP-51TS User Manual Download Page 23

Page: 23 / 44

Compact Scaler Switcher

Comm-Tec S.r.l.

www.comm-tec.it

Command

Function

Feedback Example

50614%

Set the picture mode

Picture Mode: xx (xx= dynamic/
standard/ mild/ user)

50655%

Freeze output image

Freeze: enable

50656%

Cancel the freezing of output image

Freeze: disable

50646%

Enable MIC Volume Icon display

Volume Icon: enable

50647%

Disable MIC Volume Icon display

Volume Icon: disable

50761%

Disable the mute icon of Source audio
display

Source Mute Icon: disable

50762%

Enable the mute icon of Source audio
display

Source Mute Icon: enable

50763%

Disable the mute icon of MIC audio
display

MIC Mute Icon: disable

50764%

Enable the mute icon of MIC audio
display

MIC Mute Icon: enable

50765%

Enable the freeze icon display

Freeze Icon: enable

50766%

Disable freeze icon display

Freeze Icon: disable

50644%

Enable channel status display

Input Icon: enable

50645%

Disable channel status display

Input Icon: disable

50650%

Check the channel status

Input Icon: xx

50606%

Auto-adjust the input parameter(VGA
only)

VGA Input Auto

50699%

Check the system version

Version Vx.x.x

50688%

Enable MIC noise detecting

MIC detect: enable

50689%

Disable MIC noise detecting

MIC detect: disable

50690%

Check MIC noise detecting statue

MIC detect: XXXX

50791%

HDCP Active mode

HDCP Active

50792%

HDCP Manual mode

HDCP Manual

50793%

Enable HDCP output

HDCP ON

50794%

Disable HDCP output

HDCP OFF

50795%

Inquire HDCP/ Manual HDCP

HDCP Manual

HDCP OFF/ON

Summary of Contents for UP-51TS












































Search results

Summary of Contents for UP-51TS

Reviews:

Related manuals for UP-51TS

Brands by name

Popular brands

Comm-Tec UP-51TS, User Manual

Search results

Summary of Contents for UP-51TS

Reviews:

Related manuals for UP-51TS

Brands by name

Popular brands