background image

15

104270

OWNER’S MANUAL

TROUBLESHOOTING

Continued

 WARNING: If you smell gas

• Shut off gas supply.
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your

building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the

gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

IMPORTANT: 

Operating heater where impurities in air exist may create odors. Cleaning

supplies, paint, paint remover, cigarette smoke, cements and glues, new carpet or textiles,
etc., create fumes. These fumes may mix with combustion air and create odors.

OBSERVED PROBLEM

Heater produces unwanted odors

Heater shuts off in use (ODS operates)

Gas odor even when control knob is in OFF
position

Gas odor during combustion

Moisture/condensation noticed on windows

POSSIBLE CAUSE

1. Heater burning vapors from paint, hair

spray, glues, etc. (See 

IMPORTANT

statement above)

2. Low fuel supply
3. Gas leak. 

See Warning statement at

top of page

1. Not enough fresh air is available

2. Low line pressure
3. ODS/pilot is partially clogged

1. Gas leak. 

See Warning statement at

top of page

2. Control valve defective

1. Foreign matter between control valve

and burner

2. Gas leak. 

See Warning statement at

top of page

1. Not enough combustion/ventilation air

REMEDY

1. Ventilate room. Stop using odor-causing

products while heater is running

2. Refill supply tank
3. Locate and correct all leaks (see  Check-

ing Gas Connections, page 10)

1. Open window and/or door for ventila-

tion

2. Contact local propane/LP gas company
3. Clean ODS/pilot (see Cleaning and

Maintenance, page 12)

1. Locate and correct all leaks (see  Check-

ing Gas Connections, page 10)

2. Replace control valve

1. Take apart gas tubing and remove for-

eign matter

2. Locate and correct all leaks (see  Check-

ing Gas Connections, page 10)

1. Refer to Fresh Air for Combustion and

Ventilation requirements (page 4)

www.desatech.com

Summary of Contents for CGP10LA





















Reviews: