background image

Installation and Operation Instructions

P/N 900568-00 

 

 REV.  E   03/2020

Models

INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.

This appliance may be installed in an aftermarket permanently located, manufactured (mobile) home, 

where not prohibited by local codes. This appliance is only for use with the type of gas indicated on the 

rating plate. This appliance is not convertible for use with other gases.

This is an unvented gas-fired heater. It uses air (oxygen) from the room in which it is installed. Provisions 

for adequate combustion and ventilation air must be provided. Refer to Air for Combustion and Ventilation 

section on 

Page 6

 of this manual.

PFS

®

US

Report No. F09-121

P900568-00

Westerly32ZMN

Westerly32ZMP

Vent-Free Remote Control Gas Fireplace System

       WARNING: If the information in this manual is not followed exactly, a fire or explosion may result 

causing property damage, personal injury or loss of life.

–  Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other 

appliance.

–  WHAT TO DO IF YOU SMELL GAS

•  Do not try to light any appliance. 
•  Do not touch any electrical switch; do not use any phone in your building. 
• Immediately call your gas supplier from a neighbor’s phone.  Follow the gas supplier’s instructions. 
•  If you cannot reach your gas supplier, call the fire department.

–   Installation and service must be performed by a qualified installer, service agency or the gas supplier.

Summary of Contents for Westerly32ZMN





































Reviews: