Comdial DIGITECH, System Manual

Page: 155 / 218

l
Selection
2: Line group assignment (assigns line to
line groups, will be reserved the hybrii strap is not
installed)
l
Selection
3: Line dialing mode (pulse or tone to
match the connected line)
l
Selection
4: Line privacy release (releases privacy
on a line)
Selectlon
5: Line toll restriction table assignment
l
Selection
6: Line abandoned hold release time
l
Selection
7: Set up a line (Using a model line)
(provides a means of programming a group of lines
to match the programming of a model line)
l
Selection
8: Assign name to line.
l
Selection
9: Assign line to department.
l
Selectlon 10:
Exclusive hold.
l
Selection 11:
Voice mail line ID (Specifies
identification number of a particular line to the voice
mail accessory for personalized call coverage)
l
Selection
12: assignment (Assigns to
lines and specifies calling characteristics of them)
Station C.O.S. Programming
1. Set Up a Station (Using a Model Station)
2. Assign Name to Station
3. Assign Station to Department
4. Assign Station
to
SOHVA Group
5. Line/ Intercom Features
6. Ringing Assignment
7. Button Mapping
8. Toll Restriction Administration
9. Automatic Busy/ RNA Call Forwarding
10. Miscellaneous Feature Programming
11. Return To Previous Menu
Enter Selection:
STATION COS MENU SELECTION
66-083
System Programming ,
l
Selectlon
2: Assign name to station
l
Selection
3: Assign station to department
l
Selectlon 4:
Assign station to SOHVA groups
Selectlon
5: Line/Intercom features
l
Prime Line (assign prime line, prime group,
prime intercom, or clear all)
. Ringing Line Preference (enable or disable)
l
Line Access Deny (enable or disable station
access to a line)
l
Line Originate Deny (enable or disable station
ability to originate a call on a line)
l
Idle Line Preference (enable or disable access
to an idle line when station is taken off hook)
l
Block Voice Announce Intercom Call
l
Audible Monitoring (audible ringing sounded for
stations with BLF appearance at programmed
station)
In each station COS menu selection, after choosing
the feature, enter a station port number which is to be
assigned to it and enter line port ‘numbers where . . .
prompted. station number entries are allowed
for some features as prompted.
l
Selectlon 1:
Set up a station (Using a model
station) (program a group of stations to match the
programming of a model station)
l
Selection 6:
Ringing assignment
l
Personal Ringing Tones (One of four different
tones can be chosen. Refer to page 4-29 for
frequencies if required.)
l
Direct/Delayed Ringing (of each line assigned to
programmed station)
l
Night Ringing (enable or disable night transfer,
of ringing, to programmed station for
programmed lines)
l
7: Button mapping (assign functions to
buttons)
Special Note: buttons are identified by
Ax and Bx codes as shown in Figure on page
449 and on fhe programming overlay supplied
with the system, do not type an
“B” before
the number when identifying it for function
assignment. To do so, causes the system to
interpret the typed entry as a line number choice
instead of a button number choice.
l
Functions that can be assigned are identified per
the following list:
To display list, enter
Return to key mapping with
Control
BLK . . . . . . . . . Blank
Line (1 24)
(10 57)
DND . . . . . . . . Do Not Disturb
PRI . . . . . . . . . . Privacy
. . . . . . . . . . 2nd Intercom
SAV . . . . . . . . . Save
ACC . . . . . . . . Account Code Button
. . . . . . . . . Zone
Page (l-3)
AC . . . . . . . All Call
ACB . . . . . . . . Auto Callback
C F . . . . . . . . . . . Call Forward
4-89