ComAp InteliLite MRS16 Manual Download Page 193

Page: 193 / 632

InteliLite Global Guide

193

Subgroup: ECU Settings

Setpoint group

Engine settings

Related FW

1.2.1

Range [units]

Primary / Secondary / Default [-]

Default value

Default

Alternative config

Step

[-]

Comm object

10266

Related applications

AMF, MRS

Config level

Advanced

Setpoint visibility

Visible only if ECU is configured

Description

This setpoint is used for choosing a frequency of ECU. Values are saved in ECU.

VOLVO EMSII (GE engines)

The nominal speed is selected via the VP Status proprietary frame, parameter "Frequency select".

SCANIA EMS/S6

The nominal speed is selected via parameters "Nominal speed switch 1" and "Nominal speed switch 2" in

the DLN1 proprietary frame.

Note:

To lock this setpoint against editing you also have to lock setpoint

ECU Frequency Select 1 (page

297)

and

ECU Frequency Select 2 (page 298)

ECU Frequency Select

back to List of setpoints

Setpoint group

Engine settings

Related FW

1.2.1

Range [units]

0 .. 100 [%]

Default value

50 %

Alternative config

Step

1 %

Comm object

9948

Related applications

AMF, MRS

Config level

Advanced

Setpoint visibility

Visible only if ECU is configured

Description

Enables to adjust engine speed in ECU via CAN bus. Nominal speed corresponds to 50%. This setpoint

should be used only for Volvo Penta and Scania engines. It has no effect on other engine brands.

Note:

To lock this setpoint against editing you also have to lock setpoint

ECU Speed Adjustment 1 (page

297)

and

ECU Speed Adjustment 2 (page 298)

ECU Speed Adjustment

back to List of setpoints

Summary of Contents for InteliLite MRS16

























































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for InteliLite MRS16

Reviews:

Related manuals for InteliLite MRS16

Brands by name

Popular brands

ComAp InteliLite MRS16, Manual

Search results

Summary of Contents for InteliLite MRS16

Reviews:

Related manuals for InteliLite MRS16

Brands by name

Popular brands