manualshive.com logo in svg

ComAp InteliDrive Mobile, Global Manual

The ComAp InteliDrive Mobile is an advanced control product designed for efficient and reliable engine management. With its user-friendly interface, users can easily operate and monitor their equipment. For a comprehensive understanding of its features, download the Global Manual from manualshive.com for free, and unleash the full potential of your machine.

Share
Download
background image

ID-Mobile Global Guide

160

LBI: R

Related FW

2.6.0

Related applications

AMF, MRS

Comm object

161

Description

Binary output Close Load is closed/opened by Rem On/Off input edges (toggled) when running engine RPM

is over

MinLoadSpeed (page 94)

.

C

LOSE

L

OAD

(

PAGE

170)

can be disconnected from external terminal

when

R

EM

O

N

/O

FF

(

PAGE

160)

is closed.

Rem On/Off

6

back to List of LBI

Related FW

2.6.0

Related applications

AMF, MRS

Comm object

172

Description

Activates engine start when active in RUN mode and controller ready state.

It is not possible to stop engine by panel STOP button and by Binary input Remote stop when Rem

start/stop is active. This input can be configured to Binary output Timer active to enable engine automatic

start/stop function.

Rem Start/Stop

6

back to List of LBI

Related FW

2.6.0

Related applications

AMF, MRS

Comm object

12

Description

Controller is switched to OFF mode if input is closed and back to previous mode after is opened.

Note:

Remote OFF will switch controller to OFF mode even if the Access code or Remote lock is active

or Controller mode is password protected.

Remote OFF

6

back to List of LBI

Related FW

2.6.0

Related applications

AMF, MRS

Comm object

156

Description

External “edge sensitive” request for engine start. Binary input is active in both SS and AS application.

Unsuccessful start is recorded to Alarm list and History. Binary input REMOTE START signal is equivalent

to external terminal Start button.

Note:

The second edge on Binary input Remote start skips the Idle time when engine is running in Idle

state.

Remote Start

6

back to List of LBI

Summary of Contents for InteliDrive Mobile






































































































































































































































































Reviews:

No comments

Related manuals for InteliDrive Mobile

Panasonic FP7 Series Additional Functions Manual preview
FP7 Series
Brand: Panasonic Pages: 45
ZETRON MAX Connection Manual preview
MAX
Brand: ZETRON Pages: 3
ADEMCO MAX Programming Instructions preview
MAX
Brand: ADEMCO Pages: 2
GAUGEMASTER COMBI Manual preview
COMBI
Brand: GAUGEMASTER Pages: 2
EasyIO FC Series Firmware Upgrade User Manual preview
FC Series
Brand: EasyIO Pages: 19
Zero 88 FLX Copying Manual preview
FLX
Brand: Zero 88 Pages: 2
Zenit FLX Use And Maintenance Instructions preview
FLX
Brand: Zenit Pages: 24
PAC 212 Install Manual preview
212
Brand: PAC Pages: 17
CALEFFI 145 Series Installation And Commissioning Manual preview
145 Series
Brand: CALEFFI Pages: 12
CALEFFI QuickSetter+ 132 Series User Manual preview
QuickSetter+ 132 Series
Brand: CALEFFI Pages: 5
E-T-A EtherNetIP ControlPlex CPC12EN User Manual preview
EtherNetIP ControlPlex CPC12EN
Brand: E-T-A Pages: 28
Maestra 8080 User Manual preview
8080
Brand: Maestra Pages: 22
Raypak RayTemp Installation & Operating Instructions Manual preview
RayTemp
Brand: Raypak Pages: 24
J+J S 20 Handbook preview
S 20
Brand: J+J Pages: 91
tau K125M Installation Manuals preview
K125M
Brand: tau Pages: 9
tau K100M Translation Of Original Instructions preview
K100M
Brand: tau Pages: 8
Technische Alternative UVR 63H Operation And Installation Manual preview
UVR 63H
Brand: Technische Alternative Pages: 68
TechGrow Humi DualPro User Manual preview
Humi DualPro
Brand: TechGrow Pages: 34

Brands by name

Popular brands

Load more brands