manualshive.com logo in svg

ComAp InteliDrive DCU Marine, Manual

The ComAp InteliDrive DCU Marine is a cutting-edge control unit designed for marine applications. Access its comprehensive functionality with ease by downloading the user-friendly Reference Manual from our website, available for free. Empower your marine operations with this exceptional product from ComAp.

Share
Download
background image

InteliDrive DCU Marine - 3.0.0 Global Guide

220

Source: RPU unit

Values of ID-RPU unit are available (visible) only when ID-RPU module is selected. States does not activate

Alarms.

Following list contains ID-RPU Shut down inputs state that can be configured to Binary outputs.

RPU-SD 1

Indication of ID-RPU Shut down 1 input state.

RPU-SD 2

Indication of ID-RPU Shut down 2 input state.

RPU-SD 3

Indication of ID-RPU Shut down 3 input state.

RPU-SD 4

Indication of ID-RPU Shut down 4 input state.

RPU-SD 5

Indication of ID-RPU Shut down 5 input state.

EmStop RPU

Indication of ID-RPU Emergency stop input state.

Related FW

3.0.0

Related applications

RPU

Comm object

10213

Description

Binary output Fuel solenoid (

FS

) status when output is

opened

:

0

OK

1

Fail: Broken wire (

BW

)

Table 8.1 FS-Status

Note:

The High Current is indicated if output current is over 1A approx.

FS-Status

6

back to List of LBO

Related FW

3.0.0

Related applications

RPU

Comm object

10213

Description

Binary output Fuel solenoid (

FS

) status when output is

opened

:

0

OK

1

Fail: Broken wire (

BW

)

Table 8.2 FS-Load

FS-Load

6

back to List of LBO

Related FW

3.0.0

Related applications

RPU

Comm object

10213

Description

Binary output Stop solenoid (SS) status when output is closed – see

FS-Status (page 220)

SS-Status

6

back to List of LBO

Summary of Contents for InteliDrive DCU Marine






























































































































































































































































































Reviews:

No comments

Related manuals for InteliDrive DCU Marine

Bard ECU Series Advanced Programming & Features preview
ECU Series
Brand: Bard Pages: 8
Bardiani Valvole B925 Use And Maintenance Manual preview
B925
Brand: Bardiani Valvole Pages: 35
Cansec H1000 Installation Manual And Instructions For Use preview
H1000
Brand: Cansec Pages: 45
Cansec CP40 Installation Manual preview
CP40
Brand: Cansec Pages: 43
Cansec MAP2 Installation Manual preview
MAP2
Brand: Cansec Pages: 32
VAT 150 Series Installation, Operating, & Maintenance Instructions preview
150 Series
Brand: VAT Pages: 27
Idemia MorphoAccess SIGMA Extreme Series Quick User Manual preview
MorphoAccess SIGMA Extreme Series
Brand: Idemia Pages: 31
ICP DAS USA ET-7000 series User Manual preview
ET-7000 series
Brand: ICP DAS USA Pages: 148
ICMA S001 Technical Information Sheet preview
S001
Brand: ICMA Pages: 8
NAPCO MFA6000 Operating & Installation Instructions Manual preview
MFA6000
Brand: NAPCO Pages: 48
NAPCO Magnum Alert 2600 Operating & Installation Instructions Manual preview
Magnum Alert 2600
Brand: NAPCO Pages: 68
Uniden UBC-RH96 Owner'S Manual preview
UBC-RH96
Brand: Uniden Pages: 28
UniFocus Time Clock Manager'S Manual preview
Time Clock
Brand: UniFocus Pages: 23
UniFocus Time Clock Wireless Connection Manual preview
Time Clock
Brand: UniFocus Pages: 6
ABB RHD8000 Series Instructions Manual preview
RHD8000 Series
Brand: ABB Pages: 17
Quinny Buzz 01638 User Manual preview
Buzz 01638
Brand: Quinny Pages: 21
Reliance Foundry R-7651-EM Installation preview
R-7651-EM
Brand: Reliance Foundry Pages: 3
Wesa AE04 Installation And Operation Manual preview
AE04
Brand: Wesa Pages: 8

Brands by name

Popular brands

Load more brands