ComAp InteliDrive DCU Marine Manual Download

Page: 128 / 285

InteliDrive DCU Marine - 3.0.0 Global Guide

128

Setpoint group

Engine params

Related FW

3.0.0

Range [units]

0 .. 600 [s]

Default value

Step

Comm object

8780

Related applications

All

Config level

Standard

Setpoint visibility

Always

Description

This is the time the binary output Prelubrication is active. The controller will activate binary output

Prelubrication for this amount of time, then pause for PrelubrPause, then activate again. This will continue

the entire time the engine is not running. Function is not active in controller OFF mode.

PrelubrTime

back to List of setpoints

Setpoint group

Engine params

Related FW

3.0.0

Range [units]

1 .. 4000 [min]

Default value

Step

Comm object

8781

Related applications

All

Config level

Standard

Setpoint visibility

Always

Description

Time interval between prelubrication cycles –

PrelubrTime (page 128)

Note:

To use Prelubrication, configure Binary output Prelubrication at first.

Prelubrication is disabled in controller OFF mode or when PrelubrTime is set to zero.

When engine is running Prelubrication binary output is opened.

Prelubrication starts PrelubrPause after engine stops. Prelubrication starts immediately when:

- controller power supply turns on

- mode changes from OFF to another

- Emergency Stop is released

PrelubrPause

back to List of setpoints

Summary of Contents for InteliDrive DCU Marine






























































































































































































































































































Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands

ComAp InteliDrive DCU Marine, Manual

Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands