ComAp IG-NT GC Reference Manual Download

Page: 106 / 260

IGS-NT-BC, SW Version 1.2.0,

©ComAp – January 2019

IGS-NT-BC-1.2.0 Reference Guide.PDF

106

V unbal

, which is calculated as maximum difference between two phase voltages.

The protection activates if the voltage unbalance gets over the threshold for time
longer than

Bank V unb del

OTE

The voltage unbalance protection is created in the default archive using the
mechanism of

universal analog protections

. That means

this setpoint is one of

general-purpose setpoints

, which may be used for different purpose if the

protection is deleted from the configuration.

Setpoint: Bank V unb del

Group

Bank protect

Range [units]

0.0 .. 600.0 [s]

Related FW

3.0

Description

This setpoint adjusts the delay for the generator voltage unbalance protection.
The threshold for the protection is adjusted by setpoint

Bank V unbal

OTE

The generator voltage unbalance protection is created in the default archive using
the mechanism of

universal analog protections

. That means

this setpoint is one

of general-purpose setpoints

, which may be used for different purpose if the

protection is deleted from the configuration.

Setpoint: Bank I unbal

Group

Bank protect

Range [units]

0 .. 200 [%]

Related FW

3.0

Description

This setpoint adjusts the threshold level for the generator current unbalance
protection. The threshold is adjusted in % of the generator

nominal current

. The

protection is

Breaker open and cool down

type and

is created in the default

archive as universal analog protection

at the value

Gen I unbal

, which is

calculated as maximum difference between two phase currents.

The protection activates if the current unbalance gets over the threshold for time
longer than

Bank I unb del

OTE

The current unbalance protection is created in the default archive using the
mechanism of

universal analog protections

. That means

this setpoint is one of

general-purpose setpoints

, which may be used for different purpose if the

protection is deleted from the configuration.

Setpoint: Bank I unb del

Group

Bank protect

Range [units]

0.0 .. 600.0 [s]

Summary of Contents for IG-NT GC





































































































































































































































































Search results

Summary of Contents for IG-NT GC

Reviews:

Related manuals for IG-NT GC

Brands by name

Popular brands

ComAp IG-NT GC, Reference Manual

Search results

Summary of Contents for IG-NT GC

Reviews:

Related manuals for IG-NT GC

Brands by name

Popular brands