manualshive.com logo in svg

ComAp IA-NT, Manual

Share
Download
ComAp IA-NT Manual Download Page 31

Accessory Modules for IL-NT, IC-NT, IA-NT and ID-Lite Global Guide

31

Power

LED status

Description

Dark

No required power connected

Quick flashing

Program check failure

One flash and pause

Compensation fail

Three flashes and

pause

Compensation successful

Flashes

There is no communication between IGS-PTM and the controller.

Lights

Power supply is in the range and communication between IGS-PTM and

controller properly works.

4.5.6 Wiring

Note:

It is not necessary to connect analog inputs COM terminal to negative power supply.

Long wires resistance compensation

Process of compensation:

Short all wires to analog sensors at the end (replace sensors with shorting links).

Hold the compensation button on IGS-PTM through the hole in upper cover when switching IGS-PTM on.

Result of compensation will be shown in 2 seconds by flashing of POWER LED.

One flash and pause – compensation fail.

Three flashes and pause – compensation success.

Measured lead’s resistance is stored in EEPROM memory (separate value for each input) and is

subtracted from measured value when resistance measuring.

Summary of Contents for IA-NT


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands