background image

 

Page 10 of 15

 

INSTRUCTION MANUAL

 

LI-400C 

LINE IMPEDANCE STABILIZATION NETWORK 

 

1912 1 El  T oro  Rd   ●   S il vera d o, C al ifornia  926 76  ●  ( 94 9)  459- 9600    ●   com -p ow er.com

 

                

 

 

      REV0221   

5.0

 

P

RODUCT 

D

ESCRIPTION

 

5.1 Overview 

The  LI-400C  Line  Impedance  Stabilization  Network  is  specifically  designed  to 
provide  necessary  measurement  platform  for  performing  power  line  conducted 
emissions (disturbance measurements) compliance testing in accordance with Mil 
Std 461.

 

  

 

 The LI-400C performs each of the following functions during the measurement: 

•  provides  a  defined,  stable  impedance  throughout  the  measurement 

frequency range; 

• isolates the EUT and measurement circuit from the power source, thereby 

minimizing its influence on the measurements; and, 

•  couples  the  disturbance  voltages  to  the  coaxial  measurement  port  for 

connection  to  the  measuring  instrument  like  EMI  Receiver  or  Spectrum 
Analyzer. 

5.2 Product Setup 

Before initiating use of LISN, ensure that, 

 

• PE conductor is connected to ground. 
• The ventilation openings are unobstructed. 
•  No  signal  or  operating  voltages  above  the  permissible  limits  given  in 

specification. 

• The LISN’s power input port is connected to an appropriate power source 

employing properly rated mains protection, as over current protection is 
not provided in the LISN. 

 

Failure to comply with any of these points may damage the equipment and/or 
pose an electrical hazard. 

5.2.1  Typical connection diagrams 

The  LISNs  can  be  used  with  single  phase  power  sources  with  one  set  of 
LISNs and also three phase power sources (requires two sets of LISNs). Given 
below are the typical connection setup’s for each configuration. 

 

 
 
 
 

Figure 1: Single Phase connection with one set of LISN

 

Distributed by: Reliant EMC LLC,  +1 408 916

5750,  [email protected], www.reliantemc.com

Summary of Contents for LI-400C
















Reviews: