background image

 

Page 15 of 15

 

INSTRUCTION MANUAL

 

LI-400C 

LINE IMPEDANCE STABILIZATION NETWORK 

 

1912 1 El  T oro  Rd   ●   S il vera d o, C al ifornia  926 76  ●  ( 94 9)  459- 9600    ●   com -p ow er.com

 

                

 

 

      REV0221   

8.0

 

  W

ARRANTY 

 

Com-Power warrants to its Customers that the products it manufactures will be free from 
defects  in  materials  and  workmanship  for  a  period  of  three  (3)  years.  This  warranty  shall 
not apply to: 

 

Transport damages during shipment from your plant.   

 

Damages due to poor packaging. 

 

Products operated outside their specifications. 

 

Products Improperly maintained or modified. 

 

Consumable items such as fuses, power cords, cables, etc. 

 

Normal wear  

 

Calibration 

 

Products shipped outside the United States without the prior knowlege of Com-
Power. 

In  addition,  Com-Power  shall  not  be  obliged  to  provide  service  under  this  warranty  to 
repair  damage  resulting  from  attempts  to  install,  repair,  service  or  modify the  instrument 
by personnel other than Com-Power service representatives. 

Under  no  circumstances  does  Com-Power  recognize  or  assume  liability  for  any  loss, 
damage  or  expense  arising,  either  directly  or  indirectly,  from  the  use  or  handling  of  this 
product,  or any inability to  use this product separately or in combination  with any other 
equipment. 

When  requesting  warranty  services,  it  is  recommended  that  the  original  packaging 
material be used for shipping.  Damage due to improper packaging will void warranty. 

If  you  feel  that  the  product  is  not  working  as  intended,  or  is  malfunctioning,  please 
contact Com-Power for assistance. 

In the case of repair or complaint, Please visit our 

website 

www.com-power.com

  and  fill  out  RMA  form  (

http://com-

power.com/repairservicereq.asp

).  Our  customer  service  personnel 

The  RMA 

number  should  be  displayed  in  a  prominent  location  on  the  packaging  and  on  the  
product, along with a description of the problem, and your contact information.           

                 

 

8.1 Maintenance 

 

This product contain no user serviceable parts inside. If the unit does not operate 
or needs calibration, please contact Com-Power Corporation. Any modifications 
or  repairs  performed  on  the  unit  by  someone  other  than  an  authorized  factory 
trained technician will void warranty. 
 
The exterior surface may be cleaned with mild detergent and then be wiped with 
a  dry,  clean,  lint-free  cloth.  Use  care  to  avoid  liquids  or  other  foreign  objects 
entering the chassis. 

 

Distributed by: Reliant EMC LLC,  +1 408 916

5750,  [email protected], www.reliantemc.com

Summary of Contents for LI-400C
















Reviews: