background image

e. Persons  suffering  from  obesity  or with  a  medical  history  of heart  disease,  low  or  high  blood 

pressure, circulatory system problems, or diabetes should consult a physician before using a spa 
or hot tub.

f.

Persons using medication should consult a physician before using a spa or hot tub since some 
medication may induce drowsiness while other medication may affect heart rate, blood pressure, 
and circulation. 

11.

  SAFETY WARNING—

For models provided with Audio equipment:

a.

CAUTION—

Risk of Electric Shock.  Do not leave compartment door open.

b.

CAUTION—

Risk of Electric Shock.  Replace components only with identical components.

c. Do not operate the audio/video controls while inside the spa.

d.

WARNING—

Prevent Electrocution.  Do not connect auxiliary components (for example cable, 

additional speakers, headphones, additional audio/video components, etc.) to the system.

e. These units are not provided with an outdoor antennae; when provided, it should be installed in 

accordance with Article 810 of the National Electrical Code, ANSI/NFPA 70.

f.

Do   not   service   this   product   yourself   as   opening   or   removing   covers   may   expose   you   to 
dangerous voltage or other risk of injury.  Refer all servicing to qualified service personnel.

g. When the power supply connections or power supply cord(s) are damaged; if water is entering 

the  audio/video  compartment  or  any  electrical   equipment  compartment  area;  if  the  protective 
shields  or  barriers  are  showing  signs  of  deterioration;  or  if there  are  signs  of  other   potential 
damage to the unit, turn off the unit and refer servicing to a qualified service personnel.

h. This   unit   should   be   subjected   to   periodic   routine   maintenance   (for   example,   once   every   3 

months) to make sure that the unit is operating properly.

SAVE THESE INSTRUCTIONS

SAFETY PRECAUTIONS

Never use your spa while under the influence of alcohol.

A. WARNING:  PEOPLE WITH INFECTIOUS DISEASES SHOULD NOT USE A SPA OR HOT 

TUB

B. WARNING:  TO AVOID INJURY EXERCISE CARE WHEN ENTERING OR EXITING THE SPA 

OR HOT TUB

C. WARNING:  DO NOT USE A SPA OR HOT TUB IMMEDIATELY FOLLOWING STRENUOUS 

EXERCISE

D. WARNING:  PROLONGED IMMERSION IN A SPA OR HOT TUB MAY BE INJURIOUS TO 

YOUR HEALTH

E. CAUTION:  MAINTAIN WATER CHEMISTRY IN ACCORDANCE WITH MANUFACTURER’S 

INSTRUCTIONS

Summary of Contents for Aeware

































Reviews: