background image

.05.

Cautions:

 For added protection mount the fixtures in areas outside walking paths, 

seating areas, or in areas were the fixture might be reached by unauthorized personnel.

Before mounting the fixture to any surface, make sure that the installation area can 

hold a minimum point load of 10 times the device’s weight.

Fixture installation must always be secured with a secondar y safety attachment, such 

as an appropriate safety cable.

Never stand directly below the device when mounting, removing, or servicing the 

fixture.  

OPERATION INSTRUCTIONS

5

INSTALLATIONS

6

· 

 

The LEDPAR 64UV is an LED wash light for on-site decoration purpose.

· 

 

Don’t turn on the fixture if it’s been through severe temperature difference like 

after transportation because it might damage the light due to the environment 

changes. So make sure to operate the fixture until it is in normal temperature.

· 

 

This light should be keep away from strong shaking during any transportation or 

movement.

· 

 

Don’t pull up the light by only the head, or it might cause damages to the 

mechanical parts.

· 

 

Don’t expose the fixture in overheat, moisture or environment with too much dust 

when installing it.  And don’t lay any power cables on the floor. Or it might cause 

electronic shock to the people. 

· 

 

Make sure the installation place is in good safety condition before installing the 

fixture.

· 

 

Make sure to put the safety chain and check whether the screws are screwed 

properly when installing the fixture.

· 

 

Make sure the lens are in good condition. It’s recommended to replace the units if 

there are any damages or severe scratch.

· 

 

Make sure the fixture is operated by qualified personnel who knows the fixture 

before using.

· 

 

Keep the original packages if any second shipment is needed.

· 

 

Don’t tr y to change the fixtures without any instruction by the manufacturer or 

the appointed repairing agencies. 

· 

 

It is not in warranty range if there are any malfunctions from not following the 

user manual to operate or any illegal operation, like shock short circuit, electronic 

shock , lamp broke, etc.

Summary of Contents for SI-027













Reviews: