18
Lighting Main Burners
Lighting Side Burner
1. Push and turn the side burner control knob counterclockwise to the “HIGH” position.
(Fig. 35)
2. Immediately press and hold the electronic igniter button (Fig. 35).
You will hear a snapping sound.
3. If the burner does not light in 4 seconds, turn the control knob to OFF and wait 5 minutes for
the gas to clear before trying again.
4. If the burner does not light on the second try, turn the control knob to OFF and wait 5
minutes for the gas to clear, and then try match-lighting the side burner.
1. Strike and place the burning long wooden match (or butane lighter with extension) through
the spaces in the pot support to the ports of the burner (Fig. 36).
2. Push and turn the side burner control knob counterclockwise to the “HIGH” position.
Match Lighting - Side Burner
CAUTION
Use a LONG wooden match or a butane lighter with an extension. Make sure all burner
controls are off except for the burner being lighted. If a long-reach match or lighter is not
accessible, there is a match extension provided, attached to the inside of the door. Insert
a match in the holder end of the extension, strike and place the burning match near the
BURNER being operated.
1. Push and turn one of the main burner control knobs counterclockwise to the “HIGH”
position.
Wait 5 seconds.
(Fig. 31, 32, and 33)
2. Press and hold the electronic igniter button. You will hear a snapping sound. (Fig. 33)
3. If the burner does not light in 4 seconds, turn the control knob to OFF and wait 5 minutes for
the gas to clear before trying again.
4. Repeat steps 1 through 3 to light the remaining burners.
5. If the burner does not light on the second try, turn the control knob to OFF and wait 5
minutes for the gas to clear, and then try match-lighting the burner.
Match Lighting - Main Burners
1. Strike and place the burning long wooden match (or butane lighter with extension) through
the spaces in the grill grates near the ports of the back crossover burner between the heat
tents. (Fig. 34).
2. Push and turn the control knob counterclockwise to the “HIGH” position.
3. Repeat steps 1 and 2 to light the remaining burners.
Fig. 33
Fig. 32
CAUTION
The side burner cover MUST BE OPEN during lighting and while using the side
burner (Fig. 37). NEVER operate the side burner with the side burner cover in the
closed position.
CAUTION
Use a LONG wooden match, match extension, or butane lighter with extension.
Fig. 34
WARNING
• The grill must be level before using the side burner.
• NEVER move the grill with a pot or pan on the side burner.
• Make sure the pot or pan is centered on the side burner.
• To avoid the possibility of tipping over the grill, NEVER place more than 15 pounds on
the side burner. A filled 6-quart aluminum pot weighs approximately 15 pounds.
Fig. 35
Fig. 36
15
NATURAL GAS CONVERSION KIT (not shown)
Part Number
Description
9992-225
8300 Series LP to NG Conversion Kit
Natural Gas Installation — 8300 Series
NOTE:
This step applies to you only if you are converting your 8300 Series grill to use NATURAL GAS. If
you will be using your grill with LP GAS, this section does not apply to you. Please skip back to the
section titled “
LP Cylinder Installation”
.
Y
OUR
N
ATURAL GAS COMPANY
MUST
INSTALL AND
CONNECT THE GAS SUPPLY LINE TO THE GRILL
.
The 8300 Series Grill is set up at the factory for use with LP GAS. A NATURAL GAS Conversion Kit is
available and must be purchased separately. Follow the installation instructions provided with the
Natural Gas Conversion Kit.
