background image

9

10

FUNCTIONAL DESCRIPTION

9

2

8

10

4

3

5

6

1

7

1.  Variable Speed Switch
2.  Forward/Reverse Button
3.  Torque Adjustment Collar
4.  Keyless Chuck
5.  Dual Range Gearing

6.  LED Work Light
7.  Battery Pack
8.  Battery Pack Release Button
9.  Screwdriver Bit Holder
10. Bubble Level

Model No. 500101

INSTALLING & REMOVING THE BATTERY FROM THE TOOL

SAFETY WARNINGS & INSTRUCTIONS

Figure B

Figure C

OPERATING INSTRUCTIONS

TRIGGER SWITCH & REVERSING BUTTON (FIGURE D)

•  The drill is turned ON and OFF by pulling and releasing  

the trigger switch 

(1)

. The farther the trigger is depressed,  

the higher the speed of the drill.

•  A forward/reverse control button 

(2)

 determines the direction 

of the tool and also serves as a lock off button.

•  To select forward rotation, release the trigger switch and 

depress the forward/reverse control button to the left.

•  To select reverse, depress the forward/reverse control button 

the opposite direction.

NOTE:

 

The center position of the control button locks the tool in the off position. 

When changing the position of the control button, be sure the trigger is released.

Figure D

1. Hold drill firmly with one hand on the grip 

and the other hand on the bottom of the 
battery pack.

2. When attaching accessories in the drill 

chuck, hand tightens the keyless chuck 
firmly.

WARNING

Make certain the lock-off button is engaged to prevent switch actuation before removing 
or installing battery.

WARNING

Drill may stall (if overloaded or improperly 
used) causing a twist. Always expect 
the stall. Grip the drill firmly with both 
hands to control the twisting action 
and prevent loss of control, which could 
cause personal injury. If a stall does occur, 
release the trigger immediately and 
determine the reason for the stall before 
re-starting.

TO INSTALL BATTERY PACK:

Insert battery pack into tool until an audible 

click is heard 

(figure B)

. Make sure battery 

pack is fully seated and fully latched into 

position.

TO REMOVE BATTERY PACK:

Depress the battery release button and pull 

battery pack out of tool 

(figure C)

.

DRILL SPECIFICATIONS

No Load Speed  ................................ 0~400 RPM (low) 
                           ..............................0~1400 RPM (high)
Motor  .......................................................... 20V DC Motor
Chuck  ............................................................... 1/2” Keyless
Gear Train  ..............................................................  2 Speed

Clutch  ............................................................. 20 Positions
Switch  .......................................................  Variable Speed
Charging Voltage  .............................. 120V / 60 Hz AC
Charge Rate  ................................. 1 hour Fast Charging 

Summary of Contents for 500174
















Reviews: