Press
the
>
key to go into temperature selection screen. (See figure 7-14).
Figure
7-14
Press
the
∧
key to make the 100’s temperature value selection. Press the
∨
key if you
wish to reduce the selected temperature value.
Press
the
>
key to go into the 10’s temperature selection screen (See figure 7-15).
Figure
7-15
Press
the
∧
key to make the 10’s temperature value selection. Press the
∨
key if you wish
to reduce the selected temperature value.
Press
the
>
key to go into the units temperature selection screen (See figure 7-16).
Figure
7-16
Press
the
∧
key to make the units temperature value selection. Press the
∨
key if you wish
to reduce the selected temperature value.
Press
the
>
key to return to the front screen menu.
OR…….
If 10 seconds elapse without a key being pressed the display is to return to the main
display
menu.
To start the heating process press the heating key marked with the symbol .
To stop the heating process press the heating key once more.
Note:
To show heating is in operation the heat symbol will remain illuminated. The actual
temperature shown on the LCD is that seen by the internal dry block sensor.
Note:
During the heat up process the symbol will flash to indicate the set
temperature has not been reached. Once the set temperature has been reached the
flashing symbol will remain constantly illuminated. To accommodate over / under
temperature oscillation the symbol will not recommence flashing until the temperature is
± 5°C off of the set temperature.
Note:
(When used with external probe) the temperature range setting for a ambient
+5°C to 220°C settable in increments of 1 °C
15
Page 15 of 28 Digi-Mantle M7754 issue 14.4
Press the
>
key to go into temperature selection screen. (See figure 7-14).
Figure 7-14.
Press the
^
key to make the 100’s temperature value selection. Press the
v
key if
you wish to reduce the selected temperature value.
Press the
>
key to go into the 10’s temperature selection screen (See figure 7-15).
Figure 7-15.
Press the
^
key to make the 10’s temperature value selection. Press the
v
key if
you wish to reduce the selected temperature value.
Press the
>
key to go into the units temperature selection screen (See figure 7-16).
Figure 7-16.
Press the
^
key to make the units temperature value selection. Press the
v
key if
you wish to reduce the selected temperature value.
Press the
>
key to return to the front screen menu.
OR…….
If 10 seconds elapse without a key being pressed the display is to return to the
main display menu.
To start the heating process press the heating key marked with the symbol
.
To stop the heating process press the heating key once more.
Note:
To show heating is in operation the heat symbol will remain illuminated. The
actual temperature shown on the LCD is that seen by the internal dry block sensor.
Note:
During the heat up process the
will flash to indicate the set temperature
has not been reached. Once the set temperature has been reached the flashing
symbol will remain constantly illuminated. To accommodate over / under
temperature oscillation the symbol will not recommence flashing until the
temperature is ± 5
°
C off of the set temperature.
Note:
(When used with external probe) the temperature range setting for a ambient
+5
°
C to 220
°
C settable in increments of 1
°
C
Page 14 of 28 Digi-Mantle M7754 issue 14.3
7.6. Heat setting and activation.
7.6.1. Setting the temperature when using a Mantle cartridge without internal
sensor.
From the main display menu screen press the
<
key to go into the ‘Heat setting’
screen. (See figure 7-11).
Figure 7-11.
Note:
The default setting will always display 00%. Previous power settings are not
retained.
Press the
>
key to go into set power selection screen. (See figure 6-12).
Figure 7-12.
Press the
^
key to make the
%
power selection. Press the
v
key if you wish to
reduce the power selection.
Note:
The power settings are made in increments of 5
°
C. The power selection
range is from 0 to 100%.
Press the
>
key to return to the front screen menu.
OR…….
If 10 seconds elapse without a key being pressed the display is to return to the
main display menu.
To start the heating process press the heating key marked with the symbol
.
To stop the heating process, press the heating key once more.
Note.
To show heating is in operation the heat symbol will remain illuminated. The
power percentage shown on the LCD is that of the setting.
7.6.2. Setting the temperature when using Mantle cartridge using the external
probe.
Note:
With the external probe attached an
e
symbol will appear in the LCD next to
the temperature reading indicating the connection of the external probe (See Figure
7-9). The Temperature reading displayed is that read by the probe.
The external probe is to be placed in the sample solution. Heating your sample is
now controlled via the external probe.
From the main display menu screen press the
<
key to go into the ‘Temperature
setting’ screen. (See figure 7-13).
Figure 7-13.
Note:
the Stir temperature displayed is that of the last setting made by the user.
Page 14 of 28 Digi-Mantle M7754 issue 14.3
7.6. Heat setting and activation.
7.6.1. Setting the temperature when using a Mantle cartridge without internal
sensor.
From the main display menu screen press the
<
key to go into the ‘Heat setting’
screen. (See figure 7-11).
Figure 7-11.
Note:
The default setting will always display 00%. Previous power settings are not
retained.
Press the
>
key to go into set power selection screen. (See figure 6-12).
Figure 7-12.
Press the
^
key to make the
%
power selection. Press the
v
key if you wish to
reduce the power selection.
Note:
The power settings are made in increments of 5
°
C. The power selection
range is from 0 to 100%.
Press the
>
key to return to the front screen menu.
OR…….
If 10 seconds elapse without a key being pressed the display is to return to the
main display menu.
To start the heating process press the heating key marked with the symbol
.
To stop the heating process, press the heating key once more.
Note.
To show heating is in operation the heat symbol will remain illuminated. The
power percentage shown on the LCD is that of the setting.
7.6.2. Setting the temperature when using Mantle cartridge using the external
probe.
Note:
With the external probe attached an
e
symbol will appear in the LCD next to
the temperature reading indicating the connection of the external probe (See Figure
7-9). The Temperature reading displayed is that read by the probe.
The external probe is to be placed in the sample solution. Heating your sample is
now controlled via the external probe.
From the main display menu screen press the
<
key to go into the ‘Temperature
setting’ screen. (See figure 7-13).
Figure 7-13.
Note:
the Stir temperature displayed is that of the last setting made by the user.
Page 15 of 28 Digi-Mantle M7754 issue 14.4
Press the
>
key to go into temperature selection screen. (See figure 7-14).
Figure 7-14.
Press the
^
key to make the 100’s temperature value selection. Press the
v
key if
you wish to reduce the selected temperature value.
Press the
>
key to go into the 10’s temperature selection screen (See figure 7-15).
Figure 7-15.
Press the
^
key to make the 10’s temperature value selection. Press the
v
key if
you wish to reduce the selected temperature value.
Press the
>
key to go into the units temperature selection screen (See figure 7-16).
Figure 7-16.
Press the
^
key to make the units temperature value selection. Press the
v
key if
you wish to reduce the selected temperature value.
Press the
>
key to return to the front screen menu.
OR…….
If 10 seconds elapse without a key being pressed the display is to return to the
main display menu.
To start the heating process press the heating key marked with the symbol
.
To stop the heating process press the heating key once more.
Note:
To show heating is in operation the heat symbol will remain illuminated. The
actual temperature shown on the LCD is that seen by the internal dry block sensor.
Note:
During the heat up process the
will flash to indicate the set temperature
has not been reached. Once the set temperature has been reached the flashing
symbol will remain constantly illuminated. To accommodate over / under
temperature oscillation the symbol will not recommence flashing until the
temperature is ± 5
°
C off of the set temperature.
Note:
(When used with external probe) the temperature range setting for a ambient
+5
°
C to 220
°
C settable in increments of 1
°
C
Page 15 of 28 Digi-Mantle M7754 issue 14.4
Press the
>
key to go into temperature selection screen. (See figure 7-14).
Figure 7-14.
Press the
^
key to make the 100’s temperature value selection. Press the
v
key if
you wish to reduce the selected temperature value.
Press the
>
key to go into the 10’s temperature selection screen (See figure 7-15).
Figure 7-15.
Press the
^
key to make the 10’s temperature value selection. Press the
v
key if
you wish to reduce the selected temperature value.
Press the
>
key to go into the units temperature selection screen (See figure 7-16).
Figure 7-16.
Press the
^
key to make the units temperature value selection. Press the
v
key if
you wish to reduce the selected temperature value.
Press the
>
key to return to the front screen menu.
OR…….
If 10 seconds elapse without a key being pressed the display is to return to the
main display menu.
To start the heating process press the heating key marked with the symbol
.
To stop the heating process press the heating key once more.
Note:
To show heating is in operation the heat symbol will remain illuminated. The
actual temperature shown on the LCD is that seen by the internal dry block sensor.
Note:
During the heat up process the
will flash to indicate the set temperature
has not been reached. Once the set temperature has been reached the flashing
symbol will remain constantly illuminated. To accommodate over / under
temperature oscillation the symbol will not recommence flashing until the
temperature is ± 5
°
C off of the set temperature.
Note:
(When used with external probe) the temperature range setting for a ambient
+5
°
C to 220
°
C settable in increments of 1
°
C
