5
3.
SAFETY INFORMATION
This product has been designed for safe operation when used as detailed in accordance
with the manufacturer’s instructions.
ATTENTION:
- The product will not restart after a mains electrical supply
interruption once the supply has been returned.
NOTE:
Failure to use this equipment in accordance with the manufactures operating
instructions may compromise your basic safety protection afforded by the equipment
and may invalidate the warranty / guarantee. The warranty / guarantee does not cover
damaged caused by faulty installation or misuse of the equipment.
3.1. Prevention of Fire and Electric shock.
To prevent a risk of fire or electric shock,
do not
open your product case
without authorisation. Only Qualified Service Personnel should attempt to
repair this product.
Replace fuses only with the type as listed in section, ‘Technical Specification
and Parts and Accessories’ (See fuse type and rating).
Ensure the mains power supply conforms to the rating found on the data
plate located on the back of the base controller of this Omni Reaction Station.
Never
operate this equipment with out connection to earth / ground. Ensure
the mains supply voltage is correctly earthed / grounded in accordance with
current area legislation.
3.2. General Safe Operating Practice.
Always follow good laboratory practice when using this equipment. Give due
recognition to your company’s safety and legislative health & safety procedures
and all associated legislation applicable to your areas of operation. Check
laboratory procedures for substances being heated and ensure all hazards (e.g.
explosion, implosion or the release of toxic or flammable gases) that might
arise have been suitably addressed before proceeding. When heating certain
substances the liberation of hazardous gases may require the use of a fume
cupboard or other means of extraction.
Ensure the equipment is used on a clean, dry, non-combustible, solid work
surface with at least 300mm suitable clearance all around from other equipment.
Do not
position the product so that it is difficult to disconnect from the mains
supply.
Do not
touch the heating element, dry block, cooling plug, reflux unit, hoses or
any glass vessel whilst in use.
Do not
leave a disconnected cooling plug in a dry block whilst heating. Pressure
may build up inside the cooling plug from previously used coolant and may eject
hot coolant under pressure.
Do not
lean or stretch over equipment, glassware and fixings when in use.
Do not
immerse unit in water or fluids.
Page 5 of 24 M6493 Issue 10.3
3. SAFETY INFORMATION.
This product has been designed for safe operation when used as detailed in
accordance with the manufacturer’s instructions.
NOTE:
Failure to use this equipment in accordance with this instruction book may
compromise your basic safety protection afforded by the equipment and may
invalidate the warranty / guarantee. The warranty / guarantee does not cover
damaged caused by faulty installation or misuse of the equipment.
3.1. Prevention of Fire and Electric shock.
To prevent a risk of fire or electric shock,
DO NOT
open your
product case without authorisation. Only qualified Service
personnel should attempt to repair this Controller.
Replace fuses only with the type as listed in section, Parts and
Accessories and Technical Specifications. (See fuse type and
rating).
Ensure the Mains Power Supply conforms to rating found on the
data plate located on the base of this product.
Never
Operate this equipment with out connection to earth /
ground. Ensure the mains supply voltage is correctly earthed /
grounded in accordance with current area legislation.
Do not
install or remove any heating apparatus from the controller
whilst power is applied.
3.2. General Safe Operating Practice.
Always follow good laboratory practice when using this
equipment. Give due recognition to your company’s safety and
legislative health & safety procedures and all associated legislation
applicable to your areas of operation. Check laboratory procedures
for substances being heated and ensure all hazards (e.g. explosion,
implosion or the release of toxic or flammable gases) that might
arise have been suitably addressed before proceeding. When
heating certain substances the liberation of hazardous gases may
require the use of a fume cupboard or other means of extraction.
Ensure equipment is used on a clean, dry, non-combustible, solid
work surface with at least 300mm suitable clearance all around
from other equipment.
Do not
position the product so that it is difficult to disconnect from
the mains supply.
Do not
immerse unit in water or fluids.
Do not
spill substances onto this unit. If spillage does occur,
disconnect unit from mains supply and follow instructions as
detailed in Section ‘Maintenance’.
To prevent electronic overheat and potential fire
Do not
cover this product when connected to the mains power
supply.
It is
not
recommended to leave any heating apparatus unattended
during operation.
Only use Original Equipment manufacture’s spares and
accessories. Ref Section 11.
Page 5 of 24 M6493 Issue 10.3
3. SAFETY INFORMATION.
This product has been designed for safe operation when used as detailed in
accordance with the manufacturer’s instructions.
NOTE:
Failure to use this equipment in accordance with this instruction book may
compromise your basic safety protection afforded by the equipment and may
invalidate the warranty / guarantee. The warranty / guarantee does not cover
damaged caused by faulty installation or misuse of the equipment.
3.1. Prevention of Fire and Electric shock.
To prevent a risk of fire or electric shock,
DO NOT
open your
product case without authorisation. Only qualified Service
personnel should attempt to repair this Controller.
Replace fuses only with the type as listed in section, Parts and
Accessories and Technical Specifications. (See fuse type and
rating).
Ensure the Mains Power Supply conforms to rating found on the
data plate located on the base of this product.
Never
Operate this equipment with out connection to earth /
ground. Ensure the mains supply voltage is correctly earthed /
grounded in accordance with current area legislation.
Do not
install or remove any heating apparatus from the controller
whilst power is applied.
3.2. General Safe Operating Practice.
Always follow good laboratory practice when using this
equipment. Give due recognition to your company’s safety and
legislative health & safety procedures and all associated legislation
applicable to your areas of operation. Check laboratory procedures
for substances being heated and ensure all hazards (e.g. explosion,
implosion or the release of toxic or flammable gases) that might
arise have been suitably addressed before proceeding. When
heating certain substances the liberation of hazardous gases may
require the use of a fume cupboard or other means of extraction.
Ensure equipment is used on a clean, dry, non-combustible, solid
work surface with at least 300mm suitable clearance all around
from other equipment.
Do not
position the product so that it is difficult to disconnect from
the mains supply.
Do not
immerse unit in water or fluids.
Do not
spill substances onto this unit. If spillage does occur,
disconnect unit from mains supply and follow instructions as
detailed in Section ‘Maintenance’.
To prevent electronic overheat and potential fire
Do not
cover this product when connected to the mains power
supply.
It is
not
recommended to leave any heating apparatus unattended
during operation.
Only use Original Equipment manufacture’s spares and
accessories. Ref Section 11.
Page 5 of 24 M6493 Issue 10.3
3. SAFETY INFORMATION.
This product has been designed for safe operation when used as detailed in
accordance with the manufacturer’s instructions.
NOTE:
Failure to use this equipment in accordance with this instruction book may
compromise your basic safety protection afforded by the equipment and may
invalidate the warranty / guarantee. The warranty / guarantee does not cover
damaged caused by faulty installation or misuse of the equipment.
3.1. Prevention of Fire and Electric shock.
To prevent a risk of fire or electric shock,
DO NOT
open your
product case without authorisation. Only qualified Service
personnel should attempt to repair this Controller.
Replace fuses only with the type as listed in section, Parts and
Accessories and Technical Specifications. (See fuse type and
rating).
Ensure the Mains Power Supply conforms to rating found on the
data plate located on the base of this product.
Never
Operate this equipment with out connection to earth /
ground. Ensure the mains supply voltage is correctly earthed /
grounded in accordance with current area legislation.
Do not
install or remove any heating apparatus from the controller
whilst power is applied.
3.2. General Safe Operating Practice.
Always follow good laboratory practice when using this
equipment. Give due recognition to your company’s safety and
legislative health & safety procedures and all associated legislation
applicable to your areas of operation. Check laboratory procedures
for substances being heated and ensure all hazards (e.g. explosion,
implosion or the release of toxic or flammable gases) that might
arise have been suitably addressed before proceeding. When
heating certain substances the liberation of hazardous gases may
require the use of a fume cupboard or other means of extraction.
Ensure equipment is used on a clean, dry, non-combustible, solid
work surface with at least 300mm suitable clearance all around
from other equipment.
Do not
position the product so that it is difficult to disconnect from
the mains supply.
Do not
immerse unit in water or fluids.
Do not
spill substances onto this unit. If spillage does occur,
disconnect unit from mains supply and follow instructions as
detailed in Section ‘Maintenance’.
To prevent electronic overheat and potential fire
Do not
cover this product when connected to the mains power
supply.
It is
not
recommended to leave any heating apparatus unattended
during operation.
Only use Original Equipment manufacture’s spares and
accessories. Ref Section 11.
Page 5 of 24 M6493 Issue 10.3
3. SAFETY INFORMATION.
This product has been designed for safe operation when used as detailed in
accordance with the manufacturer’s instructions.
NOTE:
Failure to use this equipment in accordance with this instruction book may
compromise your basic safety protection afforded by the equipment and may
invalidate the warranty / guarantee. The warranty / guarantee does not cover
damaged caused by faulty installation or misuse of the equipment.
3.1. Prevention of Fire and Electric shock.
To prevent a risk of fire or electric shock,
DO NOT
open your
product case without authorisation. Only qualified Service
personnel should attempt to repair this Controller.
Replace fuses only with the type as listed in section, Parts and
Accessories and Technical Specifications. (See fuse type and
rating).
Ensure the Mains Power Supply conforms to rating found on the
data plate located on the base of this product.
Never
Operate this equipment with out connection to earth /
ground. Ensure the mains supply voltage is correctly earthed /
grounded in accordance with current area legislation.
Do not
install or remove any heating apparatus from the controller
whilst power is applied.
3.2. General Safe Operating Practice.
Always follow good laboratory practice when using this
equipment. Give due recognition to your company’s safety and
legislative health & safety procedures and all associated legislation
applicable to your areas of operation. Check laboratory procedures
for substances being heated and ensure all hazards (e.g. explosion,
implosion or the release of toxic or flammable gases) that might
arise have been suitably addressed before proceeding. When
heating certain substances the liberation of hazardous gases may
require the use of a fume cupboard or other means of extraction.
Ensure equipment is used on a clean, dry, non-combustible, solid
work surface with at least 300mm suitable clearance all around
from other equipment.
Do not
position the product so that it is difficult to disconnect from
the mains supply.
Do not
immerse unit in water or fluids.
Do not
spill substances onto this unit. If spillage does occur,
disconnect unit from mains supply and follow instructions as
detailed in Section ‘Maintenance’.
To prevent electronic overheat and potential fire
Do not
cover this product when connected to the mains power
supply.
It is
not
recommended to leave any heating apparatus unattended
during operation.
Only use Original Equipment manufacture’s spares and
accessories. Ref Section 11.
Page 5 of 24 M6493 Issue 10.3
3. SAFETY INFORMATION.
This product has been designed for safe operation when used as detailed in
accordance with the manufacturer’s instructions.
NOTE:
Failure to use this equipment in accordance with this instruction book may
compromise your basic safety protection afforded by the equipment and may
invalidate the warranty / guarantee. The warranty / guarantee does not cover
damaged caused by faulty installation or misuse of the equipment.
3.1. Prevention of Fire and Electric shock.
To prevent a risk of fire or electric shock,
DO NOT
open your
product case without authorisation. Only qualified Service
personnel should attempt to repair this Controller.
Replace fuses only with the type as listed in section, Parts and
Accessories and Technical Specifications. (See fuse type and
rating).
Ensure the Mains Power Supply conforms to rating found on the
data plate located on the base of this product.
Never
Operate this equipment with out connection to earth /
ground. Ensure the mains supply voltage is correctly earthed /
grounded in accordance with current area legislation.
Do not
install or remove any heating apparatus from the controller
whilst power is applied.
3.2. General Safe Operating Practice.
Always follow good laboratory practice when using this
equipment. Give due recognition to your company’s safety and
legislative health & safety procedures and all associated legislation
applicable to your areas of operation. Check laboratory procedures
for substances being heated and ensure all hazards (e.g. explosion,
implosion or the release of toxic or flammable gases) that might
arise have been suitably addressed before proceeding. When
heating certain substances the liberation of hazardous gases may
require the use of a fume cupboard or other means of extraction.
Ensure equipment is used on a clean, dry, non-combustible, solid
work surface with at least 300mm suitable clearance all around
from other equipment.
Do not
position the product so that it is difficult to disconnect from
the mains supply.
Do not
immerse unit in water or fluids.
Do not
spill substances onto this unit. If spillage does occur,
disconnect unit from mains supply and follow instructions as
detailed in Section ‘Maintenance’.
To prevent electronic overheat and potential fire
Do not
cover this product when connected to the mains power
supply.
It is
not
recommended to leave any heating apparatus unattended
during operation.
Only use Original Equipment manufacture’s spares and
accessories. Ref Section 11.
Page 5 of 24 M6493 Issue 10.3
3. SAFETY INFORMATION.
This product has been designed for safe operation when used as detailed in
accordance with the manufacturer’s instructions.
NOTE:
Failure to use this equipment in accordance with this instruction book may
compromise your basic safety protection afforded by the equipment and may
invalidate the warranty / guarantee. The warranty / guarantee does not cover
damaged caused by faulty installation or misuse of the equipment.
3.1. Prevention of Fire and Electric shock.
To prevent a risk of fire or electric shock,
DO NOT
open your
product case without authorisation. Only qualified Service
personnel should attempt to repair this Controller.
Replace fuses only with the type as listed in section, Parts and
Accessories and Technical Specifications. (See fuse type and
rating).
Ensure the Mains Power Supply conforms to rating found on the
data plate located on the base of this product.
Never
Operate this equipment with out connection to earth /
ground. Ensure the mains supply voltage is correctly earthed /
grounded in accordance with current area legislation.
Do not
install or remove any heating apparatus from the controller
whilst power is applied.
3.2. General Safe Operating Practice.
Always follow good laboratory practice when using this
equipment. Give due recognition to your company’s safety and
legislative health & safety procedures and all associated legislation
applicable to your areas of operation. Check laboratory procedures
for substances being heated and ensure all hazards (e.g. explosion,
implosion or the release of toxic or flammable gases) that might
arise have been suitably addressed before proceeding. When
heating certain substances the liberation of hazardous gases may
require the use of a fume cupboard or other means of extraction.
Ensure equipment is used on a clean, dry, non-combustible, solid
work surface with at least 300mm suitable clearance all around
from other equipment.
Do not
position the product so that it is difficult to disconnect from
the mains supply.
Do not
immerse unit in water or fluids.
Do not
spill substances onto this unit. If spillage does occur,
disconnect unit from mains supply and follow instructions as
detailed in Section ‘Maintenance’.
To prevent electronic overheat and potential fire
Do not
cover this product when connected to the mains power
supply.
It is
not
recommended to leave any heating apparatus unattended
during operation.
Only use Original Equipment manufacture’s spares and
accessories. Ref Section 11.
Page 5 of 24 M6493 Issue 10.3
3. SAFETY INFORMATION.
This product has been designed for safe operation when used as detailed in
accordance with the manufacturer’s instructions.
NOTE:
Failure to use this equipment in accordance with this instruction book may
compromise your basic safety protection afforded by the equipment and may
invalidate the warranty / guarantee. The warranty / guarantee does not cover
damaged caused by faulty installation or misuse of the equipment.
3.1. Prevention of Fire and Electric shock.
To prevent a risk of fire or electric shock,
DO NOT
open your
product case without authorisation. Only qualified Service
personnel should attempt to repair this Controller.
Replace fuses only with the type as listed in section, Parts and
Accessories and Technical Specifications. (See fuse type and
rating).
Ensure the Mains Power Supply conforms to rating found on the
data plate located on the base of this product.
Never
Operate this equipment with out connection to earth /
ground. Ensure the mains supply voltage is correctly earthed /
grounded in accordance with current area legislation.
Do not
install or remove any heating apparatus from the controller
whilst power is applied.
3.2. General Safe Operating Practice.
Always follow good laboratory practice when using this
equipment. Give due recognition to your company’s safety and
legislative health & safety procedures and all associated legislation
applicable to your areas of operation. Check laboratory procedures
for substances being heated and ensure all hazards (e.g. explosion,
implosion or the release of toxic or flammable gases) that might
arise have been suitably addressed before proceeding. When
heating certain substances the liberation of hazardous gases may
require the use of a fume cupboard or other means of extraction.
Ensure equipment is used on a clean, dry, non-combustible, solid
work surface with at least 300mm suitable clearance all around
from other equipment.
Do not
position the product so that it is difficult to disconnect from
the mains supply.
Do not
immerse unit in water or fluids.
Do not
spill substances onto this unit. If spillage does occur,
disconnect unit from mains supply and follow instructions as
detailed in Section ‘Maintenance’.
To prevent electronic overheat and potential fire
Do not
cover this product when connected to the mains power
supply.
It is
not
recommended to leave any heating apparatus unattended
during operation.
Only use Original Equipment manufacture’s spares and
accessories. Ref Section 11.
Page 5 of 24 M6493 Issue 10.3
3. SAFETY INFORMATION.
This product has been designed for safe operation when used as detailed in
accordance with the manufacturer’s instructions.
NOTE:
Failure to use this equipment in accordance with this instruction book may
compromise your basic safety protection afforded by the equipment and may
invalidate the warranty / guarantee. The warranty / guarantee does not cover
damaged caused by faulty installation or misuse of the equipment.
3.1. Prevention of Fire and Electric shock.
To prevent a risk of fire or electric shock,
DO NOT
open your
product case without authorisation. Only qualified Service
personnel should attempt to repair this Controller.
Replace fuses only with the type as listed in section, Parts and
Accessories and Technical Specifications. (See fuse type and
rating).
Ensure the Mains Power Supply conforms to rating found on the
data plate located on the base of this product.
Never
Operate this equipment with out connection to earth /
ground. Ensure the mains supply voltage is correctly earthed /
grounded in accordance with current area legislation.
Do not
install or remove any heating apparatus from the controller
whilst power is applied.
3.2. General Safe Operating Practice.
Always follow good laboratory practice when using this
equipment. Give due recognition to your company’s safety and
legislative health & safety procedures and all associated legislation
applicable to your areas of operation. Check laboratory procedures
for substances being heated and ensure all hazards (e.g. explosion,
implosion or the release of toxic or flammable gases) that might
arise have been suitably addressed before proceeding. When
heating certain substances the liberation of hazardous gases may
require the use of a fume cupboard or other means of extraction.
Ensure equipment is used on a clean, dry, non-combustible, solid
work surface with at least 300mm suitable clearance all around
from other equipment.
Do not
position the product so that it is difficult to disconnect from
the mains supply.
Do not
immerse unit in water or fluids.
Do not
spill substances onto this unit. If spillage does occur,
disconnect unit from mains supply and follow instructions as
detailed in Section ‘Maintenance’.
To prevent electronic overheat and potential fire
Do not
cover this product when connected to the mains power
supply.
It is
not
recommended to leave any heating apparatus unattended
during operation.
Only use Original Equipment manufacture’s spares and
accessories. Ref Section 11.
Page 5 of 24 M6493 Issue 10.3
3. SAFETY INFORMATION.
This product has been designed for safe operation when used as detailed in
accordance with the manufacturer’s instructions.
NOTE:
Failure to use this equipment in accordance with this instruction book may
compromise your basic safety protection afforded by the equipment and may
invalidate the warranty / guarantee. The warranty / guarantee does not cover
damaged caused by faulty installation or misuse of the equipment.
3.1. Prevention of Fire and Electric shock.
To prevent a risk of fire or electric shock,
DO NOT
open your
product case without authorisation. Only qualified Service
personnel should attempt to repair this Controller.
Replace fuses only with the type as listed in section, Parts and
Accessories and Technical Specifications. (See fuse type and
rating).
Ensure the Mains Power Supply conforms to rating found on the
data plate located on the base of this product.
Never
Operate this equipment with out connection to earth /
ground. Ensure the mains supply voltage is correctly earthed /
grounded in accordance with current area legislation.
Do not
install or remove any heating apparatus from the controller
whilst power is applied.
3.2. General Safe Operating Practice.
Always follow good laboratory practice when using this
equipment. Give due recognition to your company’s safety and
legislative health & safety procedures and all associated legislation
applicable to your areas of operation. Check laboratory procedures
for substances being heated and ensure all hazards (e.g. explosion,
implosion or the release of toxic or flammable gases) that might
arise have been suitably addressed before proceeding. When
heating certain substances the liberation of hazardous gases may
require the use of a fume cupboard or other means of extraction.
Ensure equipment is used on a clean, dry, non-combustible, solid
work surface with at least 300mm suitable clearance all around
from other equipment.
Do not
position the product so that it is difficult to disconnect from
the mains supply.
Do not
immerse unit in water or fluids.
Do not
spill substances onto this unit. If spillage does occur,
disconnect unit from mains supply and follow instructions as
detailed in Section ‘Maintenance’.
To prevent electronic overheat and potential fire
Do not
cover this product when connected to the mains power
supply.
It is
not
recommended to leave any heating apparatus unattended
during operation.
Only use Original Equipment manufacture’s spares and
accessories. Ref Section 11.
Page 5 of 24 M6493 Issue 10.3
3. SAFETY INFORMATION.
This product has been designed for safe operation when used as detailed in
accordance with the manufacturer’s instructions.
NOTE:
Failure to use this equipment in accordance with this instruction book may
compromise your basic safety protection afforded by the equipment and may
invalidate the warranty / guarantee. The warranty / guarantee does not cover
damaged caused by faulty installation or misuse of the equipment.
3.1. Prevention of Fire and Electric shock.
To prevent a risk of fire or electric shock,
DO NOT
open your
product case without authorisation. Only qualified Service
personnel should attempt to repair this Controller.
Replace fuses only with the type as listed in section, Parts and
Accessories and Technical Specifications. (See fuse type and
rating).
Ensure the Mains Power Supply conforms to rating found on the
data plate located on the base of this product.
Never
Operate this equipment with out connection to earth /
ground. Ensure the mains supply voltage is correctly earthed /
grounded in accordance with current area legislation.
Do not
install or remove any heating apparatus from the controller
whilst power is applied.
3.2. General Safe Operating Practice.
Always follow good laboratory practice when using this
equipment. Give due recognition to your company’s safety and
legislative health & safety procedures and all associated legislation
applicable to your areas of operation. Check laboratory procedures
for substances being heated and ensure all hazards (e.g. explosion,
implosion or the release of toxic or flammable gases) that might
arise have been suitably addressed before proceeding. When
heating certain substances the liberation of hazardous gases may
require the use of a fume cupboard or other means of extraction.
Ensure equipment is used on a clean, dry, non-combustible, solid
work surface with at least 300mm suitable clearance all around
from other equipment.
Do not
position the product so that it is difficult to disconnect from
the mains supply.
Do not
immerse unit in water or fluids.
Do not
spill substances onto this unit. If spillage does occur,
disconnect unit from mains supply and follow instructions as
detailed in Section ‘Maintenance’.
To prevent electronic overheat and potential fire
Do not
cover this product when connected to the mains power
supply.
It is
not
recommended to leave any heating apparatus unattended
during operation.
Only use Original Equipment manufacture’s spares and
accessories. Ref Section 11.
Page 5 of 24 M6493 Issue 10.3
3. SAFETY INFORMATION.
This product has been designed for safe operation when used as detailed in
accordance with the manufacturer’s instructions.
NOTE:
Failure to use this equipment in accordance with this instruction book may
compromise your basic safety protection afforded by the equipment and may
invalidate the warranty / guarantee. The warranty / guarantee does not cover
damaged caused by faulty installation or misuse of the equipment.
3.1. Prevention of Fire and Electric shock.
To prevent a risk of fire or electric shock,
DO NOT
open your
product case without authorisation. Only qualified Service
personnel should attempt to repair this Controller.
Replace fuses only with the type as listed in section, Parts and
Accessories and Technical Specifications. (See fuse type and
rating).
Ensure the Mains Power Supply conforms to rating found on the
data plate located on the base of this product.
Never
Operate this equipment with out connection to earth /
ground. Ensure the mains supply voltage is correctly earthed /
grounded in accordance with current area legislation.
Do not
install or remove any heating apparatus from the controller
whilst power is applied.
3.2. General Safe Operating Practice.
Always follow good laboratory practice when using this
equipment. Give due recognition to your company’s safety and
legislative health & safety procedures and all associated legislation
applicable to your areas of operation. Check laboratory procedures
for substances being heated and ensure all hazards (e.g. explosion,
implosion or the release of toxic or flammable gases) that might
arise have been suitably addressed before proceeding. When
heating certain substances the liberation of hazardous gases may
require the use of a fume cupboard or other means of extraction.
Ensure equipment is used on a clean, dry, non-combustible, solid
work surface with at least 300mm suitable clearance all around
from other equipment.
Do not
position the product so that it is difficult to disconnect from
the mains supply.
Do not
immerse unit in water or fluids.
Do not
spill substances onto this unit. If spillage does occur,
disconnect unit from mains supply and follow instructions as
detailed in Section ‘Maintenance’.
To prevent electronic overheat and potential fire
Do not
cover this product when connected to the mains power
supply.
It is
not
recommended to leave any heating apparatus unattended
during operation.
Only use Original Equipment manufacture’s spares and
accessories. Ref Section 11.
Page 5 of 24 M6493 Issue 10.3
3. SAFETY INFORMATION.
This product has been designed for safe operation when used as detailed in
accordance with the manufacturer’s instructions.
NOTE:
Failure to use this equipment in accordance with this instruction book may
compromise your basic safety protection afforded by the equipment and may
invalidate the warranty / guarantee. The warranty / guarantee does not cover
damaged caused by faulty installation or misuse of the equipment.
3.1. Prevention of Fire and Electric shock.
To prevent a risk of fire or electric shock,
DO NOT
open your
product case without authorisation. Only qualified Service
personnel should attempt to repair this Controller.
Replace fuses only with the type as listed in section, Parts and
Accessories and Technical Specifications. (See fuse type and
rating).
Ensure the Mains Power Supply conforms to rating found on the
data plate located on the base of this product.
Never
Operate this equipment with out connection to earth /
ground. Ensure the mains supply voltage is correctly earthed /
grounded in accordance with current area legislation.
Do not
install or remove any heating apparatus from the controller
whilst power is applied.
3.2. General Safe Operating Practice.
Always follow good laboratory practice when using this
equipment. Give due recognition to your company’s safety and
legislative health & safety procedures and all associated legislation
applicable to your areas of operation. Check laboratory procedures
for substances being heated and ensure all hazards (e.g. explosion,
implosion or the release of toxic or flammable gases) that might
arise have been suitably addressed before proceeding. When
heating certain substances the liberation of hazardous gases may
require the use of a fume cupboard or other means of extraction.
Ensure equipment is used on a clean, dry, non-combustible, solid
work surface with at least 300mm suitable clearance all around
from other equipment.
Do not
position the product so that it is difficult to disconnect from
the mains supply.
Do not
immerse unit in water or fluids.
Do not
spill substances onto this unit. If spillage does occur,
disconnect unit from mains supply and follow instructions as
detailed in Section ‘Maintenance’.
To prevent electronic overheat and potential fire
Do not
cover this product when connected to the mains power
supply.
It is
not
recommended to leave any heating apparatus unattended
during operation.
Only use Original Equipment manufacture’s spares and
accessories. Ref Section 11.
