background image

8

In Case of Contamination

 

WARNING: THE FOLLOWING PROCEDURE IS INTENDED AS A GUIDE. SHOULD SPILLAGE OF A

 

TOXIC OR HAZARDOUS FLUID OCCUR, THEN ADDITIONAL SPECIAL PRECAUTIONS MAY

 

BE NECESSARY.

If the equipment has been exposed to contamination, the Responsible Body is responsible for carrying out
appropriate decontamination. If hazardous material has been spilt on or inside the equipment, decontamination 
should only be undertaken under the control of the Responsible Body with due recognition of possible hazards. 
Before using any cleaning or decontamination method, the Responsible Body should check with the manufacturer 
that the proposed method will not damage the equipment. Prior to further use, the Responsible Body shall check 
the electrical safety of the unit. Only if all safety requirements are met can the unit be used again.

NOTE: 

In the event of this equipment or any part of the unit becoming damaged or requiring service, the item(s) 

should be returned to the manufacturer for repair accompanied by a decontamination certificate. Copies of the 
Certificate are available from the Distributor/Manufacturer.

At the end of its service life, the product must be accompanied by a Decontamination Certificate.

Repairs and Support

Any repairs or replacement of parts MUST be undertaken by suitably qualified personnel. Only spare parts supplied 
or specified by Antylia Scientific or its agents should be used. Fitting of non-approved parts may affect the per-
formance and safety features designed into the instrument. For a comprehensive list of parts required by service 
engineers conducting internal repairs please contact the service department quoting the model and serial number:

Email: [email protected]
Tel: +44 (0)1785 810475

For any other technical enquiries please contact the Technical Support Department at:
Email: [email protected]
Tel: +44 (0)1785 810433

Antylia Scientific Ltd,
Beacon Road,
Stone,
Staffordshire,
ST15 0SA,
United Kingdom
Email: [email protected]
Tel: +44 (0)1785 810475
Web: www.Cole-Parmer.com

Spares and Accessories 

Please contact your local sales specialist or email [email protected] to enquire about available spares.

Please visit www.Cole-Parmer.com for a full list of available accessories.

Summary of Contents for MH8524













Reviews: