background image

SAFETY / WARNING 

 

Please pay close attention to the safety notices in this section. 
Disregarding these notices may lead to serious injury and/or damage 
to the unit. 

 
 
 

ATTENTION 

■ 

To minimize shock and fire hazards, be sure not to overload outlet. Please designate 
one outlet for your unit. 

■ 

Do not use extension cords. 

■ 

Do not put your hands under the unit when the unit is required to be moved. 

■ 

When the unit is not in use for a long period of time, please unplug the unit from the 
outlet. 

■ 

After unplugging the unit, wait at least 10 minutes before re-plugging it. Failure to do 
so could cause damage to the compressor. 

 
 

UNPLUG CORD 

■ 

To minimize shock and fire hazards, please do not plug or unplug the cord with wet 

hands. 

■ 

During maintenance and cleaning, please unplug the unit. 

 
 

PROPER GROUNDING REQUIRED 

■ 

To minimize shock and fire hazards, make sure that the unit is properly grounded. 

 
 

PROHIBITION 

■ 

Do not attempt to remove or repair any component unless instructed by factory. 

■ 

Make sure that the unit is not resting on or against the electrical cord and plug. 

■ 

To minimize personal injury, do not hang on the doors. 

■ 

Do not store any flammable and explosive gas or liquids inside the unit. 

■ 

Do not attempt to alter or tamper with the electrical cord. 


!

 

 
 
 
 
 
 
 
 
 
 

Summary of Contents for SGD120







Reviews: