background image

5

Allow the sealant to dry thoroughly before
operating the dispenser. Please refer to the sealant
manufacturer specs on the sealant tube.

THE MACHINE IS INTENDED FOR

INDOOR USE

C) Electrical Requirements

!!! WARNING !!!

This machine must be properly grounded.
Failure to provide adequate grounding can
result in severe electrical shock and / or fatal
bodily injury.

This machine is provided with a power cord
connected to the unit. You should have already
inspected the cord for any damages that may have
occurred during shipping. If there is no damage to
the cord, you may plug it into the electrical
receptacle.

For this dispenser, you will need to provide a
dedicated electrical circuit with a rating of
115vac / 60hz / 1phase – 15amperes. This
receptacle should be no farther than 6 feet from
the dispenser and at no times should an extension
cord be used. This electrical circuit must comply
with your local and / or state regulations.

Part II – Explanation of the Controls

A) Front Touch Pad / CPU Unit

The model KW-77 machine is equipped with a
central CPU unit. This unit contains the front
touch pad, which monitors and controls the
functions of the machine. The front touch pad is
also the switching mechanism which operates the
following:
*Refrigeration of the product
*Activates the pump for dispensing
*Set the mix tank storage temperature
*Set the portion size or continuous dispense
mode
*Calibrate the temperature sensing probe
*Displays mix tank temperature

Also contained in the CPU unit is a delay timer
for the compressor. This delay will not allow the
compressor to immediately start, but delay the
start for three minutes. This delay will allow the
internal refrigerant pressures to equalize, which
will minimize high starting loads on the
compressor.

Front Switch Pad

ON

OFF

0

°F

+

t

sec.

571.2

571.1

571.4

571.3

571.5

570.2

570.1

Summary of Contents for KW-77
















Reviews: