Clean Water Systems 7500-S User Manual Download

Page: 1 / 16

Page 1

7500-S Carbon Backwash Filter Guide

www.cleanwaterstore.com

rev102418

7500-S Carbon Backwash Filter Guide

Thank you for purchasing a Clean Water System!

With proper installation and a little routine maintenance your system will be

providing clean, odor-free water for many years.

Please review this start-up guide entirely before beginning to install your

system, and follow the steps outlined for best results.

Minimum pressure of 30 PSI recommended. Maximum pressure

recommended 80 PSI. For indoor installation.

Protect from sunlight, rain, and freezing.

MEDIA CONTAINS DUST. USE MASK TO AVOID BREATHING DUST.

OK to wet down media with spray bottle.

To connect drain line to drain, use an air-gap connection.

Questions?

Call us toll-free: 1-888-600-5426 or 1-831-462-8500

Email us:

[email protected]

See more information on our website:

www.cleanwaterstore.com/resources

Clean Water Made Easy.

www.CleanWaterStore.com

Summary of Contents for 7500-S

















Search results

Summary of Contents for 7500-S

Reviews:

Related manuals for 7500-S

Brands by name

Popular brands

Clean Water Systems 7500-S, User Manual

Search results

Summary of Contents for 7500-S

Reviews:

Related manuals for 7500-S

Brands by name

Popular brands