Cold Shot Chillers ACWC-024-E-DR-LT-0-2 Page 23 Installation, Operation And Maintenance Instructions Download

Page: 23 / 28

Evaporator

Compressor

Sensing Bulb Tube

TXV

Filter/Drier

Sensing Bulb Tube

SightGlass/

Moisture

Indicator

High Pressure

Switch

Hot Gas Bypass

Valve

(Optional)

Suction Line

Service Valve/Port

Low Pressure

Switch

Flow Safety Thermostat

Liquid Line

Service Valve/Port

Head Pressure

Switch

CHILLER

(Fluid System)

Compressor

CONDENSER

Sensing Tube

Condenser

Water

OUT

Condenser

Water

Head Pressure

Control Valve

STRAINER

LIQUID

RECEIVER

Condenser Coils

Fan

Air Cooled Condenser

Water Cooled Condenser

Tandem Compressor Models only

Equalizing Tube

Suction

Accumulator*

DRAWN

ENGINEERING

ISSUED

SIZE

DETAIL

REFRIGERATION & CHILLED FLUID CIRCUIT

REV

ref.circuit

Typical Air/Water-Cooled Water Chiller (ACWC

and WCWC) Single Refrigerant Circuit System

11/12/2013

SCALE

NTS

Typical ref-circuit .vsd

SHEET

NOTES

All specifications and designs are subject to change without notice.

Hot Gas Bypass optional. For capacity and/or ambient condition use.

Temperature Controller typically monitors the tank temperature on portable models,
the entering temperature (from the process) on stationary and reverse flow models.

Flow Safety thermostat typical on indoor units or outdoors to 40F ambient, typically.

* Dependent on system design.

Additional

Fans*

Summary of Contents for ACWC-024-E-DR-LT-0-2





























Search results

Summary of Contents for ACWC-024-E-DR-LT-0-2

Reviews:

Related manuals for ACWC-024-E-DR-LT-0-2

Brands by name

Popular brands

Cold Shot Chillers ACWC-024-E-DR-LT-0-2, Installation, Operation And Maintenance Instructions

Search results

Summary of Contents for ACWC-024-E-DR-LT-0-2

Reviews:

Related manuals for ACWC-024-E-DR-LT-0-2

Brands by name

Popular brands