background image

 

 

 

 

DOMUSFIRE C29 - C35  

1.7 Reference standards 

 

Standard UNI 10683:2005 :

 

Installation requirements for heat generators burning wood or other solid biofuels;

 

Standard UNI EN14785:2006 : Requirements for design, manufacture, construction, safety and performance,     
                                                    instructions and marking, together with the relevant test methods for approval of  
                                                    units burning pellets ; 
Standard UNI EN303-5:2004 : Terminology, requirements, tests and marking relevant to Boilers for solid fuels, with   
                                                   manual and automatic feed ; 
Standard  UNI  10412-2:2009  :

 

Safety  requirements  for  domestic-type  heating  units  using  heat  generators  fed  with 

solid fuel - part 2 ; 

Standard CEI EN 60335-1 : Safety of electrical appliances for domestic and similar use - part 1; 
Standard CEI EN 60335-2-102 : Safety of electrical appliances for domestic and similar use - part 2; 
Standard CEI EN 55014-1 

Electromagnetic resistance - Requirements for electrical appliances, electric tools and  

                                              similar electrical equipment - Part 1: Interference; 

Standard CEI EN 55014-2 : Electromagnetic resistance - Requirements for electrical appliances, electric tools and  
                                              similar electrical equipment - Part 2: Immunity; Product family standard;

 

Standard CEI EN 61000-3-2

 

: Limits for harmonic current emissions (Input current 

16 A per phase);

 

Standard CEI EN 61000-3-3

 

: Limitation of voltage fluctuations and flicker in low voltage supply systems for    

                                                 equipment with nominal current 

 16 A; 

Standard CEI EN 62233 : Measuring methods for electromagnetic fields of electrical household appliances and   
                                          similar with reference to human exposure. 
Standards DIN plus 51731 - UNI EN14961-2 - Ö-Norm M 7135 : Standards regarding the specifications and   

                                                              classification of pellets. 

 

1.8 Data plate 

The  data  plate  is  visible  on  the  inside  of  the  pellet  hopper  door  or  on  the  back  of  the  boiler.  It  gives  the  following 
data. On it are listed all the technical data in the table par.1.4. 
 

 

1.9 Boiler decommissioning 

When the unit is no longer to be used, disconnect it from the power supply and empty all pellets from the hopper. For 
disposal, the boiler must be sealed inside strong packing; contact the local authority in charge of such operations in 
order  to  proceed  according  to  the  current  local  regulations,  or  take  it  to  the  dealer  when  purchasing  a  similar  new 
unit. 

 

Under Article 13 Leg. Decree No. 151 of 25 July 2005 implementing Directive 2002/96/EC of 23 February 2003 
on  Waste  Electrical  and  Electronic  Equipment  and  procedures  relating  to  measures  aimed  at  preventing  the 
production  of  waste  electrical  and  electronic  equipment,  called  WEEE,  promoting  reuse,  recycling  and  other 
forms of recovery in order to reduce the amount to be sent for disposal and improving the operation of parties 
participating in the life cycle of these products. 

 

The  barred  waste  bin  symbol  on  the  label  indicates  that,  at  the  end  of  its  service  life,  the  unit  must  be  collected 
separately from other household waste. 
 
 

1.10 Instructions for requesting assistance and replacement parts 

To  request  any  assistance  and/or  replacement  parts,  contact  the  dealer,  area  importer  or  the  nearest  authorised 
service  centre,  clearly

 

specifying  the  following:  boiler  model,  serial  number,  date  of  purchase,  list  of  replacement 

parts, details of faults or malfunctioning. 

 

- All operations on components must be carried out by authorised and/or qualified personnel. 
- Make sure all electrical connections are disconnected and that the boiler is cold before any work  
  on it. 
- Only use original replacement parts. 

 

 

Summary of Contents for DOMUSFIRE C29





































Reviews: