background image

6

6X-1110B

Grounding

• 

To provide protection against electrical surges induced by lightning, static charges, or any other 
cause, the camera and cabling system must be properly grounded to earth. For installation on a 
building, the camera must be bonded (that is, provided with a low impedance connection) to the 
building’s structural earth ground system. For installation on a metal pole with a proper ground 
system at the base, the camera must be bonded to the pole. For installation on a non-grounded or 
insulated support, the camera must be grounded with an adequate ground strap or wire between 
the camera and a nearby ground system, or to a ground system installed at the base of the sup-
port. Failure to adequately ground the camera may lead to failure of the camera. This applies to 
low voltage (i.e. PoE cameras) as well as to 115 Vac cameras. 

Failures due to surges are not 

covered by the warranty, as they are not due to defects in material or workmanship, and it is 
the installer’s responsibility to meet these grounding requirements

.

• 

All system cables must be shielded, and the shield(s) must be bonded to earth ground.

Summary of Contents for ER 8800




























Reviews: